Jetson TX1 Boot Log: Difference between revisions
mNo edit summary |
mNo edit summary |
||
| Line 1,115: | Line 1,115: | ||
</pre> | </pre> | ||
[[Category: | [[Category:Old]] | ||
Latest revision as of 18:12, 20 December 2024
Baudrate set to: 115200
Port Settings are: 8NC0S0
Port Device set to: /dev/ttyUSB0
Baudrate set to: 115200
Port Settings are: 8NC0S0
[0000.736] [TegraBoot] (version 23.00.2015.14-mobile-3a15407d)
[0000.742] Processing in cold boot mode Bootloader 2
[0000.746] A01 Bootrom Patch rev = 31
[0000.750] Power-up reason: on button
[0000.753] No Battery Present
[0000.756] Platform has Ddr4 type ram
[0000.759] max77620 disabling SD1 Remote Sense
[0000.764] Setting Ddr voltage to 1125mv
[0000.768] Serial Number of Pmic Max77663: 0x1004a4
[0000.776] Entering ramdump check
[0000.779] Get RamDumpCarveOut = 0x0
[0000.782] RamDumpCarveOut=0x0, RamDumperFlag=0xe59ff3f8
[0000.787] Last reboot was clean, booting normally!
[0000.792] Sdram initialization is successful
[0000.796] SecureOs Carveout Base=0xff800000 Size=0x00800000
[0000.801] GSC1 Carveout Base=0xff700000 Size=0x00100000
[0000.827] GSC2 Carveout Base=0xff600000 Size=0x00100000
[0000.853] GSC3 Carveout Base=0xff500000 Size=0x00100000
[0000.858] GSC4 Carveout Base=0xff400000 Size=0x00100000
[0000.863] GSC5 Carveout Base=0xff300000 Size=0x00100000
[0000.868] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000
[0000.874] Lp0 Carveout Base=0xff2bf000 Size=0x00001000
[0000.889] RamDump Carveout Base=0xff23f000 Size=0x00080000
[0000.894] Platform-DebugCarveout: 0
[0000.898] Nck Carveout Base=0xff03f000 Size=0x00200000
[0000.938] Using GPT Primary to query partitions
[0000.943] Loading Tboot-CPU binary
[0000.992] Verifying bootloader in OdmNonSecureSBK mode
[0001.002] Bootloader load address is 0xa0000000, entry address is 0xa0000258
[0001.011] Bootloader downloaded successfully.
[0001.016] Downloaded Tboot-CPU binary to 0xa0000258
[0001.021] MAX77620_GPIO1 Configured.
[0001.025] MAX77620_GPIO5 Configured.
[0001.028] CPU power rail is up
[0001.031] CPU clock enabled
[0001.035] Performing RAM repair
[0001.038] Updating A64 Warmreset Address to 0xa00002e9
[0001.055] Bootloader DTB Load Address: 0x83000000
[0001.071] Kernel DTB Load Address: 0x83080000
[0001.076] Loading cboot binary
[0001.170] Verifying bootloader in OdmNonSecureSBK mode
[0001.264] Bootloader load address is 0x8010fda8, entry address is 0x80110000
[0001.273] Bootloader downloaded successfully.
[0001.277] GPT: Partition NOT found !
[0001.281] Find Partition via GPT Failed
[0001.284] function NvTbootGetBinaryOffsets: 0x845208 error
[0001.289] Error in NvTbootLoadBinary: 0x845208 !
[0001.294] Next binary entry address: 0x80110000
[0001.298] BoardId: 2180
[0001.325] NvTbootI2cWrite(): error code 0x00045100 Error while starting write transaction
[0001.332] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave
[0001.341] NvTbootI2c: Read failed for slave 0xa2, offset 0x00 with error code 0x00045001
[0001.349] Display board id read failed
[0001.353] dram memory type is 3
[0001.357] WB0 init successful
[0001.383] Bpmp FW successfully loaded
[0001.386] Set NvDecSticky Bits
[0001.389] GSC1 address : ff700000
[0001.393] GSC2 address : ff600000
[0001.397] GSC3 address : ff500000
[0001.401] GSC4 address : ff400000
[0001.404] GSC5 address : ff300000
[0001.408] GSC MC Settings done
[0001.411] TOS old plaintext Image length 61440
[0001.417] *** Secure OS image signature not verified ***
[0001.423] Loading and Validation of Secure OS Successful
[0001.428] NvTbootPackSdramParams: start.
[0001.433] NvTbootPackSdramParams: done.
[0001.436] Tegraboot started after 126107 us
[0001.440] Basic modules init took 942242 us
[0001.444] Sec Bootdevice Read Time = 194 ms, Read Size = 8459 KB
[0001.450] Next stage binary read took 12293 us
[0001.454] Carveout took 251766 us
[0001.458] CPU initialization took 138946 us
[0001.462] Total time taken by TegraBoot 1345247 us
[0001.466] Starting CPU & Halting co-processor
64b[0001.602] LPDDR4 Training: Number of tables = 10
[0001.606] EMC Training (SRC-freq: 204000; DST-freq: 408000)
[0001.612] EMC Training Successful
[0001.615] EMC Training (SRC-freq: 204000; DST-freq: 665600)
[0001.621] EMC Training Successful
[0001.624] EMC Training (SRC-freq: 204000; DST-freq: 800000)
[0001.636] EMC Training Successful
[0001.639] EMC Training (SRC-freq: 204000; DST-freq: 1065600)
[0001.661] EMC Training Successful
[0001.664] EMC Training (SRC-freq: 204000; DST-freq: 1331200)
[0001.686] EMC Training Successful
[0001.689] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.709] EMC Training Successful
[0001.712] Switching to 800000 KHz Success
[0001.745] LPDDR4 Training: Number of tables = 10
U-Boot 2015.07-rc2 (Apr 28 2016 - 19:24:09 -0600)
TEGRA210
Model: NVIDIA P2371-2180
DRAM: 4 GiB
MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
*** Warning - bad CRC, using default environment
tegra-pcie: PCI regions:
tegra-pcie: I/O: 0x0000000012000000-0x0000000012010000
tegra-pcie: non-prefetchable memory: 0x0000000013000000-0x0000000020000000
tegra-pcie: prefetchable memory: 0x0000000020000000-0x0000000040000000
tegra-pcie: 4x1, 1x1 configuration
tegra-pcie: probing port 0, using 4 lanes
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, ignoring
tegra-pcie: probing port 1, using 1 lanes
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, ignoring
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 0
MMC: no card present
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
948 bytes read in 299 ms (2.9 KiB/s)
p2371-2180 eMMC boot options
1: primary kernel
Enter choice: 1: primary kernel
Retrieving file: /boot/Image
18951520 bytes read in 499 ms (36.2 MiB/s)
append: fbcon=map:0 console=tty0 console=ttyS0,115200n8 androidboot.modem=none androidboot.serialno=P2180A00P00940c003fd androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootreason=pmc:software_reset,pmic:0x0 root=/dev/mmcblk0p1 rw rootwait
Retrieving file: /boot/tegra210-jetson-tx1-p2597-2180-a01-devkit.dtb
250527 bytes read in 71 ms (3.4 MiB/s)
## Flattened Device Tree blob at 82000000
Booting using the fdt blob at 0x82000000
reserving fdt memory region: addr=80000000 size=20000
Using Device Tree in place at 0000000082000000, end 000000008204029e
Starting kernel ...
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.67-gbaaa7aa-dirty (dsoto@dsoto-pc) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Mon Apr 11 12:54:42 CST 2016
[ 0.000000] CPU: Cortex A57 Processor [411fd071] revision 1
[ 0.000000] alternative: enabling workaround for ARM erratum 832075
[ 0.000000] Machine: jetson_tx1
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] Tegra reserved memory:
[ 0.000000] LP0: ff2bf000 - ff2bffff
[ 0.000000] Bootloader framebuffer: 00000000 - 00000000
[ 0.000000] Bootloader framebuffer2: 00000000 - 00000000
[ 0.000000] Framebuffer: f6200000 - fa9fffff
[ 0.000000] 2nd Framebuffer: faa00000 - ff1fffff
[ 0.000000] Carveout: 00000000 - 00000000
[ 0.000000] Vpr: 00000000 - 0b9fffff
[ 0.000000] Tsec: 00000000 - 00000000
[ 0.000000] Bootloader Debug Data: 00000000 - 00000000
[ 0.000000] Nvdumper: ff23f000 - ff23ffff
[ 0.000000] cma: CMA: reserved 188 MiB at ea400000
[ 0.000000] cma: CMA: reserved 16 MiB at e9400000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] DTS File Name: arch/arm64/boot/dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts
[ 0.000000] DTB Build time: Apr 11 2016 13:11:36
[ 0.000000] Tegra21: Speedo/IDDQ fuse revision 4
[ 0.000000] Tegra21: CPU Speedo ID 7, Soc Speedo ID 0, Gpu Speedo ID 2
[ 0.000000] Tegra21: CPU Process ID 0, Soc Process ID 1, Gpu Process ID 0
[ 0.000000] Tegra21: CPU Speedo value 2067, Soc Speedo value 1992, Gpu Speedo value 2076
[ 0.000000] Tegra21: CPU IDDQ 2056, Soc IDDQ 2336, Gpu IDDQ 2870
[ 0.000000] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 Core Process: 1
[ 0.000000] tegra: PLLP fixed rate: 408000000
[ 0.000000] pll_u: boot with h/w control already set
[ 0.000000] pll_x boot misc1 0x0 : expected 0x20
[ 0.000000] (comparison mask = 0xffffff)
[ 0.000000] pll_c4 rates match 204000000 max sdmmc: vco=998400000 out0=998400000 out3=998400000
[ 0.000000] Lowering vic03 maximum rate from 1000000000 to 627200000
[ 0.000000] Lowering nvjpg maximum rate from 1000000000 to 627200000
[ 0.000000] Lowering se maximum rate from 1000000000 to 627200000
[ 0.000000] Lowering tsecb maximum rate from 1000000000 to 627200000
[ 0.000000] Lowering msenc maximum rate from 1000000000 to 716800000
[ 0.000000] Lowering nvdec maximum rate from 1000000000 to 716800000
[ 0.000000] Lowering vi maximum rate from 1000000000 to 793600000
[ 0.000000] Lowering isp maximum rate from 1000000000 to 793600000
[ 0.000000] Lowering adsp_bus maximum rate from 1200000000 to 844800000
[ 0.000000] Lowering sbus maximum rate from 600000000 to 408000000
[ 0.000000] Lowering host1x maximum rate from 600000000 to 408000000
[ 0.000000] Lowering pll_c maximum rate from 1200000000 to 1130000000
[ 0.000000] Lowering pll_c2 maximum rate from 1200000000 to 1130000000
[ 0.000000] Lowering pll_c3 maximum rate from 1200000000 to 1130000000
[ 0.000000] Lowering pll_d2 maximum rate from 1500000000 to 1130000000
[ 0.000000] Lowering pll_dp maximum rate from 1500000000 to 1130000000
[ 0.000000] Lowering sor0 maximum rate from 600000000 to 540000000
[ 0.000000] Lowering sor1 maximum rate from 600000000 to 594000000
[ 0.000000] Lowering dmic1 maximum rate from 12288000 to 12190000
[ 0.000000] Lowering dmic2 maximum rate from 12288000 to 12190000
[ 0.000000] Lowering dmic3 maximum rate from 12288000 to 12190000
[ 0.000000] Lowering hda maximum rate from 102000000 to 51000000
[ 0.000000] Lowering sdmmc2 maximum rate from 266000000 to 204000000
[ 0.000000] Lowering qspi maximum rate from 133000000 to 116600000
[ 0.000000] Lowering gbus maximum rate from 1300000000 to 998400000
[ 0.000000] Lowering cpu_g maximum rate from 3000000000 to 1734000000
[ 0.000000] Lowering cpu_lp maximum rate from 1350000000 to 1132800000
[ 0.000000] tegra dvfs: vdd_cpu: nominal 1226mV, offset 708000uV, step 19200uV, scaling enabled
[ 0.000000] tegra dvfs: vdd_core: nominal 1075mV, offset 0uV, step 12500uV, scaling enabled
[ 0.000000] tegra dvfs: vdd_gpu: nominal 1100mV, offset 710000uV, step 10000uV, scaling enabled
[ 0.000000] tegra_powergate_init: DONE
[ 0.000000] tegra21_plle_clk_enable: pll_e is already enabled
[ 0.000000] PERCPU: Embedded 13 pages/cpu @ffffffc03feb3000 s21504 r8192 d23552 u53248
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 993840
[ 0.000000] Kernel command line: fbcon=map:0 console=tty0 console=ttyS0,115200n8 androidboot.modem=none androidboot.serialno=P2180A00P00940c003fd androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootreason=pmc:software_reset,pmic:0x0 root=/dev/mmcblk0p1 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Memory: 1888MB 2048MB = 3936MB total
[ 0.000000] Memory: 3736972k/3736972k available, 293492k reserved
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000 (245759 MB)
[ 0.000000] vmemmap : 0xffffffbc01c00000 - 0xffffffbc05400000 ( 56 MB)
[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc100000000 ( 4096 MB)
[ 0.000000] .init : 0xffffffc001065000 - 0xffffffc0010d0400 ( 429 kB)
[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0010641c4 ( 16273 kB)
[ 0.000000] .data : 0xffffffc0010e4000 - 0xffffffc001292c40 ( 1724 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] NR_IRQS:960 nr_irqs:960 0
[ 0.000000] the number of interrupt controllers found is 6
[ 0.000000] Architected local timer running at 19.20MHz (phys).
[ 0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[ 0.000000] Wake16 for irq=34
[ 0.000000] Wake16 for irq=34
[ 0.000000] Enabling wake16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.016491] Calibrating delay loop (skipped), value calculated using timer frequency.. lpj=192000
[ 0.025313] pid_max: default: 32768 minimum: 301
[ 0.030018] Security Framework initialized
[ 0.034044] Mount-cache hash table entries: 256
[ 0.085685] Initializing cgroup subsys debug
[ 0.087974] Initializing cgroup subsys freezer
[ 0.092648] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[ 0.140377] ftrace: Allocated trace_printk buffers
[ 0.201165] Brought up 4 CPUs
[ 0.202151] SMP: Total of 4 processors activated.
[ 0.206851] alternatives: patching kernel code
[ 0.214675] devtmpfs: initialized
[ 0.232455] pinctrl core: initialized pinctrl subsystem
[ 0.236074] regulator-dummy: ; Rail ON
[ 0.244575] Initializing plugin-manager
[ 0.246751] node /plugin-manager/p2180-1000-300@0 match with board 2180-1000-100
[ 0.254281] NET: Registered protocol family 16
[ 0.261314] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.267150] console [pstore-1] enabled
[ 0.270025] ramoops: attached 0x200000@0xf6000000, ecc: 0/0
[ 0.276033] I2C first dynamic bus number based on alias = 7
[ 0.281199] cpuidle: using governor ladder
[ 0.285179] cpuidle: using governor menu
[ 0.289799] PMC: Setting PMIC interrupt active-low
[ 0.294551] tegra-pmc device create success
[ 0.298085] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[ 0.305219] Clear bootloader IO dpd settings
[ 0.309448] PMC: configuring io pad defaults
[ 0.313944] PMC: IO pad audio voltage is 1800000
[ 0.318387] PMC: IO pad cam voltage is 1800000
[ 0.322818] PMC: IO pad dbg voltage is 1800000
[ 0.327226] PMC: IO pad dmic voltage is 1800000
[ 0.331745] PMC: IO pad pex-ctrl voltage is 1800000
[ 0.336587] PMC: IO pad spi voltage is 1800000
[ 0.341018] PMC: IO pad uart voltage is 1800000
[ 0.345513] PMC: IO pad bb voltage is 1800000
[ 0.349845] PMC: IO pad audio-hv voltage is 1800000
[ 0.354712] PMC: IO pad spi-hv voltage is 1800000
[ 0.359380] PMC: IO pad gpio voltage is 1800000
[ 0.363898] PMC: IO pad sdmmc3 voltage is 1800000
[ 0.368475] PMC: IO pad pex-bias power is disable
[ 0.373165] PMC: IO pad pex-clk1 power is disable
[ 0.377832] PMC: IO pad pex-clk2 power is disable
[ 0.382515] T210 pmc padctrl driver initialized
[ 0.387079] T210 pmc config for bootrom command passed
[ 0.393510] INFO: pinmux CLAMP_INPUTS_WHEN_TRISTATED: disabled
[ 0.400329] clk_init_from_dt_table: clocks are set from t210-clk-init-table:clkinit-0
[ 0.409586] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[ 0.413871] platform bpmp.15: domain=ffffffc0ff04d698 allocates as[0]=ffffffc0ff1040a8
[ 0.421771] platform bpmp.15: IOVA linear map 0x00000000ff2c0000(40000)
[ 0.428713] bpmp bpmp.15: bpmp_connect returned 0
[ 0.433696] MC mapped MMIO address: 0xffffff800003a000
[ 0.437989] MC0 mapped MMIO address: 0xffffff8000072000
[ 0.443209] MC1 mapped MMIO address: 0xffffff8000098000
[ 0.460290] tegra210-pinctrl 700008d4.pinmux: lookup the user state drive not found
[ 0.466076] tegra210-pinctrl 700008d4.pinmux: Probed Tegra pinctrl driver
[ 0.473409] GPIO chip tegra-gpio: created GPIO range 0->245 ==> 700008d4.pinmux PIN 0->245
[ 0.481033] tegra-gpio 6000d000.gpio: Initialising GPIO state 0: name wlan-default
[ 0.488579] gpiochip_add: registered GPIOs 0 to 255 on device: tegra-gpio
[ 0.499020] Wake44 for irq=81
[ 0.500042] Wake40 for irq=53
[ 0.502944] Wake41 for irq=53
[ 0.505889] Wake42 for irq=53
[ 0.508835] Wake43 for irq=53
[ 0.512459] platform 70006000.serial: domain=ffffffc0ff125298 allocates as[0]=ffffffc0ff104110
[ 0.521697] platform sound.18: domain=ffffffc0ff125518 allocates as[0]=ffffffc0ff104178
[ 0.531307] platform tegradc.1: domain=ffffffc0ff125918 allocates as[0]=ffffffc0ff1041e0
[ 0.541405] platform tegradc.1: IOVA linear map 0x00000000f6200000(4800000)
[ 0.550350] platform tegradc.1: IOVA linear map 0x00000000faa00000(4800000)
[ 0.555502] platform tegradc.1: IOVA linear map 0x00000000ea400000(bc00000)
[ 0.564778] platform gpu.0: domain=ffffffc0ff125a98 allocates as[0]=ffffffc0ff104248
[ 0.570604] platform gpu.0: domain=ffffffc0ff125a98 allocates as[1]=ffffffc0ff1042b0
[ 0.578295] platform gpu.0: domain=ffffffc0ff125a98 allocates as[2]=ffffffc0ff104318
[ 0.586024] platform gpu.0: domain=ffffffc0ff125a98 allocates as[3]=ffffffc0ff104380
[ 0.599190] platform sdhci-tegra.3: domain=ffffffc0ff192098 allocates as[0]=ffffffc0ff1043e8
[ 0.606251] platform sdhci-tegra.0: domain=ffffffc0ff192298 allocates as[0]=ffffffc0ff104450
[ 0.614435] Wake39 for irq=52
[ 0.628377] gpio wake52 for gpio=61
[ 0.630301] gpio wake8 for gpio=58
[ 0.633304] gpio wake8 for gpio=58
[ 0.638183] irq: no irq domain found for /soctherm@0x700E2000 !
[ 0.642778] irq: no irq domain found for /soctherm@0x700E2000 !
[ 0.648620] board_info: id:sku:fab:major:minor = 0x0884:0x03e8:0x00:0x00:0x00
[ 0.655571] PMC dt information non-NULL tegra_init_suspend
[ 0.668562] Loading EMC tables...
[ 0.669987] tegra: Using EMC sequence '21021' for Rev. 7 tables
[ 0.675822] tegra: emc: Derated table is valid.
[ 0.680320] Lowering emc maximum rate from 1800000000 to 1600000000
[ 0.686546] tegra: validated EMC DFS table
[ 0.703520] swapper/0 isomgr_init(): iso emc max clk=1600000KHz
[ 0.707457] swapper/0 isomgr_init(): max_iso_bw=11520000KB
[ 1.969921] vdso: 2 pages (1 code, 1 data) at base ffffffc0010ea000
[ 1.974260] vdso32: 2 pages (1 code, 1 data) at base ffffffc0010e9000
[ 1.980670] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 1.987523] nvdumper: last reboot was unknown
[ 1.991752] nvdumper: set_dirty_state 0x2badface
[ 1.996866] Tegra restart notifier registered.
[ 2.013561] bio: create slab <bio-0> at 0
[ 2.017737] vdd-ac-bat: 5000 mV ; Rail ON
[ 2.020033] vdd-cpu-fixed: 1000 mV ; Rail ON
[ 2.024938] vgaarb: loaded
[ 2.027104] SCSI subsystem initialized
[ 2.030894] usbcore: registered new interface driver usbfs
[ 2.035939] usbcore: registered new interface driver hub
[ 2.041287] usbcore: registered new device driver usb
[ 2.047000] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/icm20628@68
[ 2.053241] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/ak8963@0d
[ 2.060068] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/bmp280@77
[ 2.066931] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/cm32180@48
[ 2.073860] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/iqs263@44
[ 2.080764] gpio wake33 for gpio=188
[ 2.085699] regulator_get() failed for (1-0074,vcc), -19
[ 2.089535] pca953x 1-0074: no regulator found for vcc. Assuming vcc is always powered
[ 2.098193] gpio wake21 for gpio=89
[ 2.101127] gpiochip_add: registered GPIOs 1008 to 1023 on device: tca9539
[ 2.108121] regulator_get() failed for (1-0077,vcc), -19
[ 2.113042] pca953x 1-0077: no regulator found for vcc. Assuming vcc is always powered
[ 2.121658] gpio wake36 for gpio=202
[ 2.124634] gpiochip_add: registered GPIOs 992 to 1007 on device: tca9539
[ 2.131907] i2c i2c-3: of_i2c: modalias failure on /i2c@7000c700/prod-settings
[ 2.139648] max77620 4-003c: CID0: 0xa4
[ 2.142343] max77620 4-003c: CID1: 0x04
[ 2.146130] max77620 4-003c: CID2: 0x10
[ 2.149942] max77620 4-003c: CID3: 0x59
[ 2.153776] max77620 4-003c: CID4: 0x35
[ 2.157569] max77620 4-003c: CID5: 0x80
[ 2.161403] max77620 4-003c: MAX77620 PMIC OTP Version is 0x35
[ 2.168800] max77620-pmic max77620-pmic: Consumer c2 does not have device name
[ 2.174433] max77620-pmic max77620-pmic: Consumer c0 does not have device name
[ 2.182610] vdd_core: 600 <--> 1400 mV at 1000 mV with ramp delay 27500 uV/us ; Rail ON
[ 2.190394] vddio-ddr: at 1125 mV with ramp delay 27500 uV/us ; Rail ON
[ 2.196705] vdd-pre-reg: 1350 mV with ramp delay 27500 uV/us ; Rail ON
[ 2.203736] vdd-1v8: 1800 mV with ramp delay 27500 uV/us ; Rail ON
[ 2.209526] avdd-sys: 1200 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.215117] avdd-sys: supplied by vdd-pre-reg
[ 2.220102] vdd-pex: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.225670] vdd-pex: supplied by vdd-pre-reg
[ 2.230387] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.238914] vdd-cam-hv: 2800 mV with ramp delay 100000 uV/us ; Rail OFF
[ 2.245650] vdd-rtc: 850 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.251660] avdd-ts-hv: 3300 mV with ramp delay 100000 uV/us ; Rail OFF
[ 2.258942] vdd-ts: 1800 mV with ramp delay 100000 uV/us ; Rail OFF
[ 2.264740] vdd-gen-pll-edp: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.270911] vdd-gen-pll-edp: supplied by vdd-pre-reg
[ 2.276560] vdd-hdmi-dp: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[ 2.282431] vdd-hdmi-dp: supplied by vdd-pre-reg
[ 2.287570] max77620-gpio max77620-gpio.0: Initialising GPIO state 1: name gpio_default
[ 2.295057] gpiochip_add: registered GPIOs 984 to 991 on device: max77620-gpio
[ 2.303367] max77620-gpio max77620-gpio.0: max77620 gpio successfully initialized
[ 2.313416] max77620 4-003c: max77620 probe successfully
[ 2.317584] Linux video capture interface: v2.00
[ 2.321406] pps_core: LinuxPPS API ver. 1 registered
[ 2.326275] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 2.335412] PTP clock support registered
[ 2.341272] Advanced Linux Sound Architecture Driver Initialized.
[ 2.345861] Bluetooth: Core ver 2.16
[ 2.348965] NET: Registered protocol family 31
[ 2.353369] Bluetooth: HCI device and connection manager initialized
[ 2.359689] Bluetooth: HCI socket layer initialized
[ 2.364552] Bluetooth: L2CAP socket layer initialized
[ 2.369587] Bluetooth: SCO socket layer initialized
[ 2.375931] vdd-3v3: 3300 mV ; Rail ON
[ 2.379561] max77620-gpio7: 1050 mV ; Rail ON
[ 2.382542] max77620-gpio7: supplied by vdd-gen-pll-edp
[ 2.388046] lcd-bl-en: 1800 mV ; Rail ON
[ 2.391907] en-vdd-sd: 3300 mV ; Rail OFF
[ 2.395611] en-vdd-sd: supplied by vdd-3v3
[ 2.399829] reg-fixed-sync-voltage 5.regulator: Consumer c1 does not have device name
[ 2.407911] en-vdd-cam: 1800 mV ; Rail OFF
[ 2.411569] en-vdd-cam: supplied by vdd-1v8
[ 2.422582] vdd-sys-boost: 5000 mV ; Rail ON
[ 2.425513] vdd-hdmi: 5000 mV ; Rail OFF
[ 2.428815] vdd-hdmi: supplied by vdd-3v3
[ 2.433095] aux-3v3: 3300 mV ; Rail ON
[ 2.436735] snsr_pm: 3300 mV ; Rail ON
[ 2.440981] vdd-disp-3v0: 3000 mV ; Rail ON
[ 2.444970] vdd-fan: 5000 mV ; Rail OFF
[ 2.448496] usb-vbus1: 5000 mV ; Rail OFF
[ 2.452234] usb-vbus1: supplied by vdd-3v3
[ 2.456574] usb-vbus3: 5000 mV ; Rail OFF
[ 2.460289] usb-vbus3: supplied by vdd-3v3
[ 2.464937] en-vdd-ts-1v8: 1800 mV ; Rail OFF
[ 2.469261] en-vdd-ts-hv-3v3: 3300 mV ; Rail OFF
[ 2.474000] en-vdd-disp-3v3: 3300 mV ; Rail ON
[ 2.478247] en-mdm-pwr-3v7: ; Rail OFF
[ 2.482138] en-vdd-disp-1v8: 1800 mV ; Rail ON
[ 2.486393] en-vdd-cam-hv-2v8: ; Rail OFF
[ 2.490079] rtl-5v0: ; Rail OFF
[ 2.493232] en-usb-vbus2: ; Rail OFF
[ 2.497058] en-vdd-cam-1v2: ; Rail OFF
[ 2.501145] regulator-pwm 0.pwm-regulator: PWM request deferred
[ 2.506088] platform 0.pwm-regulator: Driver regulator-pwm requests probe deferral
[ 2.514304] vdd_gpu: applied init 1000000uV constraint
[ 2.518732] vdd_gpu: 710 <--> 1320 mV at 1000 mV ; Rail OFF
[ 2.526048] vdd_cpu: applied init 1000000uV constraint
[ 2.529392] vdd_cpu: 708 <--> 1322 mV at 1000 mV normal ; Rail ON
[ 2.538258] gpio wake34 for gpio=200
[ 2.541497] extcon-gpio-states 1.extcon: Cable state 1
[ 2.547098] Switching to clocksource arch_sys_counter
[ 2.582420] No Device Node present for smmu client: tegra-carveouts !!
[ 2.586984] No Device Node present for smmu client: tegra-carveouts !!
[ 2.593643] nvmap_heap_init: nvmap_heap_init: created heap block cache
[ 2.600438] No Device Node present for smmu client: tegra-carveouts !!
[ 2.606490] dma_declare_coherent_resizable_cma_memory:278: resizable heap=vpr, base=0x0x00000000ea400000, size=0xbc00000
[ 2.617330] dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (6) rem_chunk_size(0x1c00000)
[ 2.628082] cma: enabled page replacement for spfn=ea400, epfn=f6000
[ 2.634219] dma_declare_coherent_resizable_cma_memory:325: resizable cma heap=vpr create successful
[ 2.643055] nvmap_page_pool_init: Total RAM pages: 986467
[ 2.648582] nvmap_page_pool_init: nvmap page pool size: 123308 pages (481 MB)
[ 2.655785] nvmap_background_zero_thread: PP zeroing thread starting.
[ 2.656036] misc nvmap: iram :dma coherent mem declare 0x0000000040001000,258048
[ 2.656749] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[ 2.657240] misc nvmap: created heap vpr base 0x00000000ea400000 size (192512KiB)
[ 2.657615] nvmap:inner cache maint threshold=2097152
[ 2.657616] No Device Node present for smmu client: tegra-carveouts !!
[ 2.667693] Wake39 for irq=52
[ 2.667807] tegra-otg tegra-otg: otg transceiver registered
[ 2.668419] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[ 2.669619] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[ 2.669991] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[ 2.670186] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[ 2.670376] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[ 2.671540] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra
[ 2.671785] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type Tboard_tegra
[ 2.672823] tegra21_plle_clk_enable: pll_e hw sequencer is already on
[ 2.672846] t210_sata_uphy_pll_init: init sata uphy pll
[ 2.672860] t210_sata_uphy_pll_init SATA uses SATA Lane
[ 2.673186] tegra_xusb_padctl_phy_enable: pex uphy already enabled
[ 2.674658] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sys is having fixed voltage 1800000
[ 2.674755] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-uart is having fixed voltage 1800000
[ 2.674849] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-audio is having fixed voltage 1800000
[ 2.674948] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-cam is having fixed voltage 1800000
[ 2.675060] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-pex-ctrl is having fixed voltage 1800000
[ 2.675155] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc1 is having voltages: 1800000:3300000
[ 2.675255] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc3 is having fixed voltage 1800000
[ 2.675350] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc4 is having fixed voltage 1800000
[ 2.675447] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-audio-hv is having fixed voltage 1800000
[ 2.675540] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-debug is having fixed voltage 1800000
[ 2.675649] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-dmic is having fixed voltage 1800000
[ 2.675744] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-gpio is having fixed voltage 1800000
[ 2.675845] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-spi is having fixed voltage 1800000
[ 2.675938] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-spi-hv is having fixed voltage 1800000
[ 2.676033] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc2 is having fixed voltage 1800000
[ 2.676142] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-dp is having fixed voltage 1800000
[ 2.676149] tegra210-pmc-iopower pmc-iopower.20: NO_IO_POWER setting 0x0
[ 2.676464] NET: Registered protocol family 2
[ 2.677260] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[ 2.677488] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 2.677723] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.677821] TCP: reno registered
[ 2.677832] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.677875] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.678206] NET: Registered protocol family 1
[ 2.678601] RPC: Registered named UNIX socket transport module.
[ 2.678604] RPC: Registered udp transport module.
[ 2.678608] RPC: Registered tcp transport module.
[ 2.678611] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 2.679076] tegra-fuse tegra-fuse: Fuse driver initialized succesfully
[ 2.685872] host1x host1x: initialized
[ 2.697409] NTFS driver 2.1.30 [Flags: R/O].
[ 2.697690] fuse init (API version 7.22)
[ 2.698115] msgmni has been set to 7706
[ 2.699582] io scheduler noop registered (default)
[ 2.699798] Tegra cpuquiet initialized: disabled
[ 2.702276] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails
[ 2.703324] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes and lane map as 0x14
[ 2.705388] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes and lane map as 0x14
[ 3.108404] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 3.514295] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 3.920352] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[ 3.926827] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring
[ 4.333393] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[ 4.743623] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[ 5.153582] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[ 5.160059] tegra-pcie 1003000.pcie-controller: link 1 down, ignoring
[ 5.164571] tegra-pcie 1003000.pcie-controller: PCIE: no ports detected
[ 5.171423] tegra-pcie 1003000.pcie-controller: PCIE: Disable power rails
[ 5.180386] tsec tsec: initialized
[ 5.183123] tsec tsecb: initialized
[ 5.187610] nvdec nvdec: initialized
[ 5.192611] falcon vic03: initialized
[ 5.196014] falcon msenc: initialized
[ 5.199394] falcon nvjpg: initialized
[ 5.203062] tegradc tegradc.1: Display dc.54240000 registered with id=0
[ 5.208308] display board info: id 0x0, fab 0x0
[ 5.213177] panel_select fail by _node_status
[ 5.217065] display board info: id 0x0, fab 0x0
[ 5.221827] panel_select fail by _node_status
[ 5.225845] parse_tmds_config: No tmds-config node
[ 5.230753] of_dc_parse_platform_data: could not find vrr-settings node
[ 5.237191] of_dc_parse_platform_data: could not find SD settings node
[ 5.243819] of_dc_parse_platform_data: could not find cmu node
[ 5.249498] of_dc_parse_platform_data: could not find cmu node for adobeRGB
[ 5.256461] tegradc tegradc.1: DT parsed successfully
[ 5.262656] display board info: id 0x0, fab 0x0
[ 5.266289] panel_select fail by _node_status
[ 5.270666] gpio wake53 for gpio=225
[ 5.275415] tegradc tegradc.1: probed
[ 5.282052] Console: switching to colour frame buffer device 80x30
[ 5.291419] tegradc tegradc.1: fb registered
[ 5.296668] tegra_camera_platform tegra-camera-platform.37: tegra_camera_probe:camera_platform_driver probe
[ 5.311826] tegra-apbdma tegra-apbdma: Tegra20 APB DMA driver register 32 channels
[ 5.323020] tegra-adma tegra210-adma: Tegra210 ADMA driver register 10 channels
[ 5.332762] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 5.339378] No Device Node present for smmu client: serial8250 !!
[ 5.345667] No Device Node present for smmu client: serial8250 !!
[ 5.352925] No Device Node present for smmu client: serial8250 !!
[ 5.359061] No Device Node present for smmu client: serial8250 !!
[ 5.365560] of_serial 70006000.serial: RX periodic polling enabled
[ 5.372056] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 68) is a Tegra
[ 5.379096] console [ttyS0] enabled, bootconsole disabled
[ 5.379096] console [ttyS0] enabled, bootconsole disabled
[ 5.390258] tegradc tegradc.1: hdmi: spurious interrupt
[ 5.397797] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 69) is a SERIAL_TEGRA
[ 5.410199] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 78) is a SERIAL_TEGRA
[ 5.422745] serial-tegra 70006300.serial: RX in PIO mode
[ 5.430433] 70006300.serial: ttyTHS3 at MMIO 0x70006300 (irq = 122) is a SERIAL_TEGRA
[ 5.469715] brd: module loaded
[ 5.478624] loop: module loaded
[ 5.484584] zram: Created 1 device(s) ...
[ 5.490972] nct1008_nct72 0-004c: find device tree node, parsing dt
[ 5.499521] nct1008_nct72 0-004c: starting parse dt
[ 5.506712] nct1008_nct72 0-004c: success parsing dt
[ 5.513947] nct1008_nct72 0-004c: success in enabling rail vdd_nct72
[ 5.592069] NCT72: Enabled overheat logging at 104.00C
[ 5.599359] gpio wake33 for gpio=188
[ 5.605035] nct1008_nct72 0-004c: nct1008_probe: initialized
[ 5.616066] THERMAL EST start of therm_fan_est_probe.
[ 5.623262] THERMAL EST: found 2 subdevs
[ 5.629266] THERMAL EST name: thermal-fan-est.
[ 5.635846] THERMAL EST num_resources: 0
[ 5.641850] [THERMAL EST subdev 0]
[ 5.647251] THERMAL EST subdev name: CPU-therm
[ 5.653684] THERMAL EST index 0 coeffs 50
[ 5.659627] THERMAL EST index 1 coeffs 0
[ 5.665400] THERMAL EST index 2 coeffs 0
[ 5.671099] THERMAL EST index 3 coeffs 0
[ 5.676646] THERMAL EST index 4 coeffs 0
[ 5.682101] THERMAL EST index 5 coeffs 0
[ 5.687456] THERMAL EST index 6 coeffs 0
[ 5.692723] THERMAL EST index 7 coeffs 0
[ 5.697870] THERMAL EST index 8 coeffs 0
[ 5.702988] THERMAL EST index 9 coeffs 0
[ 5.708069] [THERMAL EST subdev 1]
[ 5.712633] THERMAL EST subdev name: GPU-therm
[ 5.718217] THERMAL EST index 0 coeffs 50
[ 5.723354] THERMAL EST index 1 coeffs 0
[ 5.728366] THERMAL EST index 2 coeffs 0
[ 5.733349] THERMAL EST index 3 coeffs 0
[ 5.738233] THERMAL EST index 4 coeffs 0
[ 5.743070] THERMAL EST index 5 coeffs 0
[ 5.747817] THERMAL EST index 6 coeffs 0
[ 5.752499] THERMAL EST index 7 coeffs 0
[ 5.757126] THERMAL EST index 8 coeffs 0
[ 5.761733] THERMAL EST index 9 coeffs 0
[ 5.766306] THERMAL EST index 0: trip_temp 0, hyst 0
[ 5.771934] THERMAL EST index 1: trip_temp 51000, hyst 15000
[ 5.778234] THERMAL EST index 2: trip_temp 61000, hyst 9000
[ 5.784430] THERMAL EST index 3: trip_temp 71000, hyst 9000
[ 5.790627] THERMAL EST index 4: trip_temp 82000, hyst 10000
[ 5.796908] THERMAL EST index 5: trip_temp 140000, hyst 0
[ 5.802959] THERMAL EST index 6: trip_temp 150000, hyst 0
[ 5.809001] THERMAL EST index 7: trip_temp 160000, hyst 0
[ 5.815056] THERMAL EST index 8: trip_temp 170000, hyst 0
[ 5.821118] THERMAL EST index 9: trip_temp 180000, hyst 0
[ 5.827166] THERMAL EST index 0: trip_temps_hyst 0
[ 5.832629] THERMAL EST index 1: trip_temps_hyst 36000
[ 5.838442] THERMAL EST index 2: trip_temps_hyst 51000
[ 5.844230] THERMAL EST index 3: trip_temps_hyst 52000
[ 5.849957] THERMAL EST index 4: trip_temps_hyst 61000
[ 5.855666] THERMAL EST index 5: trip_temps_hyst 62000
[ 5.861378] THERMAL EST index 6: trip_temps_hyst 71000
[ 5.867081] THERMAL EST index 7: trip_temps_hyst 72000
[ 5.872825] THERMAL EST index 8: trip_temps_hyst 82000
[ 5.878536] THERMAL EST index 9: trip_temps_hyst 140000
[ 5.884353] THERMAL EST index 10: trip_temps_hyst 140000
[ 5.890295] THERMAL EST index 11: trip_temps_hyst 150000
[ 5.896226] THERMAL EST index 12: trip_temps_hyst 150000
[ 5.902168] THERMAL EST index 13: trip_temps_hyst 160000
[ 5.908101] THERMAL EST index 14: trip_temps_hyst 160000
[ 5.914013] THERMAL EST index 15: trip_temps_hyst 170000
[ 5.919891] THERMAL EST index 16: trip_temps_hyst 170000
[ 5.925774] THERMAL EST index 17: trip_temps_hyst 180000
[ 5.931660] THERMAL EST index 18: trip_temps_hyst 180000
[ 5.937523] THERMAL EST index 19: trip_temps_hyst 0
[ 5.942949] THERMAL EST index 20: trip_temps_hyst 0
[ 5.948358] THERMAL EST init dev[0] temp hist to 25000
[ 5.954082] THERMAL EST init dev[1] temp hist to 25000
[ 5.959792] THERMAL EST cdev_type: pwm-fan.
[ 5.964586] THERMAL EST governor name: pid_thermal_gov
[ 5.970706] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est.38
[ 5.981477] THERMAL EST: thz register success.
[ 5.986936] THERMAL EST: end of probe, return err: 0
[ 5.992955] tegra_profiler: Branch: Dev
[ 5.997760] tegra_profiler: Version: 1.104
[ 6.002857] tegra_profiler: Samples version: 34
[ 6.008413] tegra_profiler: IO version: 18
[ 6.013564] armv8_pmu: imp: 0x41, idcode: 0x1
[ 6.019010] armv8_pmu: arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0
[ 6.026983] tegra_profiler: auth: init
[ 6.032462] GPS: mt3332_gps_mod_init: platform_driver_register ret = 0
[ 6.041580] t210_sata_uphy_pll_init: sata uphy already enabled
[ 6.049517] tegra-sata tegra-sata.0: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl TEGRA-SATA mode
[ 6.061724] tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pmp pio slum part sadm apst
[ 6.075251] Rounding down aligned max_sectors from 4294967295 to 4294967288
[ 6.084675] spi-tegra114 7000d400.spi: Static pin configuration used
[ 6.093711] spi-tegra114 7000da00.spi: Static pin configuration used
[ 6.103334] tun: Universal TUN/TAP device driver, 1.6
[ 6.110462] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 6.119010] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 6.127089] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 6.136049] PPP generic driver version 2.4.2
[ 6.142656] PPP BSD Compression module registered
[ 6.149454] PPP Deflate Compression module registered
[ 6.156618] PPP MPPE Compression module registered
[ 6.163530] NET: Registered protocol family 24
[ 6.170117] usbcore: registered new interface driver r8152
[ 6.177839] usbcore: registered new interface driver asix
[ 6.185431] usbcore: registered new interface driver ax88179_178a
[ 6.193712] usbcore: registered new interface driver cdc_ether
[ 6.201729] usbcore: registered new interface driver smsc95xx
[ 6.209557] usbcore: registered new interface driver net1080
[ 6.217242] usbcore: registered new interface driver cdc_subset
[ 6.225116] usbcore: registered new interface driver zaurus
[ 6.232599] usbcore: registered new interface driver cdc_ncm
[ 6.240016] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.248785] ehci-pci: EHCI PCI platform driver
[ 6.255225] tegra_xusb_read_usb_calib: usb_calib0 = 0x07a67c0f
[ 6.264602] tegra-xhci tegra-xhci: XUSB device id = 0xfac (T210)
[ 6.272506] usb_calib0 = 0x07a67c0f
[ 6.277543] usb_calib_ext = 0x00000004
[ 6.282895] usb_calib0 = 0x07a67c0f
[ 6.287889] usb_calib_ext = 0x00000004
[ 6.293120] usb_calib0 = 0x07a67c0f
[ 6.298003] usb_calib_ext = 0x00000004
[ 6.303139] xusb_prod port0 RX_CTLE = 0xfc
[ 6.308575] xusb_prod port0 RX_DFE = 0xc0077f1f
[ 6.314436] xusb_prod port0 RX_CDR_CTRL = 0x1c7
[ 6.320272] xusb_prod port0 RX_EQ_CTRL_H = 0xfcf01368
[ 6.326609] xusb_prod port1 RX_CTLE = 0xfc
[ 6.331952] xusb_prod port1 RX_DFE = 0xc0077f1f
[ 6.337679] xusb_prod port1 RX_CDR_CTRL = 0x1c7
[ 6.343435] xusb_prod port1 RX_EQ_CTRL_H = 0xfcf01368
[ 6.350835] usbcore: registered new interface driver cdc_acm
[ 6.357807] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 6.368687] usbcore: registered new interface driver cdc_wdm
[ 6.375988] usbcore: registered new interface driver usb-storage
[ 6.383707] usbcore: registered new interface driver usbserial
[ 6.391159] usbcore: registered new interface driver ftdi_sio
[ 6.398425] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 6.408729] usbcore: registered new interface driver option
[ 6.415889] usbserial: USB Serial support registered for GSM modem (1-port)
[ 6.424479] usbcore: registered new interface driver pl2303
[ 6.431715] usbserial: USB Serial support registered for pl2303
[ 6.439347] usbcore: registered new interface driver nvshieldled
[ 6.447092] Nvidia Tegra High-Speed USB Device Controller driver (Apr 30, 2012)
[ 6.458370] tegra USB phy - inst[0] platform info:
[ 6.465063] port_otg: yes
[ 6.469552] has_hostpc: yes
[ 6.474264] phy_interface: USB_PHY_INTF_UTMI
[ 6.480505] op_mode: TEGRA_USB_OPMODE_DEVICE
[ 6.486696] qc2_voltage: 0
[ 6.491343] vbus_pmu_irq: 0
[ 6.496053] charging: enabled
[ 6.500943] remote_wakeup: disabled
[ 6.511417] regulator_get() failed for (tegra-udc.0,usb_bat_chg), -19
[ 6.519797] tegra-udc tegra-udc.0: usb_bat_chg regulator not registered: USB charging will not be enabled
[ 6.533798] mousedev: could not register psaux device, error: -16
[ 6.541921] mousedev: PS/2 mouse device common for all mice
[ 6.549738] usbcore: registered new interface driver xpad
[ 6.557316] usbcore: registered new interface driver usb_acecad
[ 6.565347] usbcore: registered new interface driver aiptek
[ 6.572921] usbcore: registered new interface driver gtco
[ 6.580242] usbcore: registered new interface driver hanwang
[ 6.587731] usbcore: registered new interface driver kbtab
[ 6.594951] otg state changed: SUSPEND --> PERIPHERAL
[ 6.601800] usbcore: registered new interface driver wacom
[ 6.708392] max77620-rtc max77620-rtc.1: rtc core: registered max77620-rtc as rtc0
[ 6.790518] Wake51 for irq=118
[ 6.795216] Enabling wake51
[ 6.799658] i2c /dev entries driver
[ 6.806603] i2c i2c-6: of_i2c: modalias failure on /i2c@546c0000/tca6408@21
[ 6.815808] virtual_init
[ 6.820867] [IMX135] sensor driver loading
[ 6.826804] [imx132] sensor driver loading
[ 6.832697] [ar0261] sensor driver loading
[ 6.838665] ov7695 sensor driver loading
[ 6.844402] mt9m114 sensor driver loading
[ 6.850380] pcl-generic pcl-generic: virtual_chip_add
[ 6.858422] usbcore: registered new interface driver uvcvideo
[ 6.865852] USB Video Class driver (1.1.1)
[ 6.872297] max77620-power-off max77620-power-off.4: Event recorder REG_NVERC : 0x0
[ 6.883901] FAN dev name: pwm-fan
[ 6.888903] FAN:gpio request success.
[ 6.894327] pwm_fan_driver pwm-fan.35: cap state:7, cap pwm:255
[ 6.902273] pwm_fan_driver pwm-fan.35: got pwm for fan
[ 6.909449] pwm_fan_driver pwm-fan.35: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[ 6.921043] pwm_fan_driver pwm-fan.35: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[ 6.932931] pwm_fan_driver pwm-fan.35: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[ 6.944965] pwm_fan_driver pwm-fan.35: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[ 6.957333] pwm_fan_driver pwm-fan.35: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[ 6.969835] pwm_fan_driver pwm-fan.35: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[ 6.982588] pwm_fan_driver pwm-fan.35: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[ 6.995698] pwm_fan_driver pwm-fan.35: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[ 7.009056] pwm_fan_driver pwm-fan.35: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[ 7.022680] pwm_fan_driver pwm-fan.35: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[ 7.038060] tegra_aotag tegra-aotag.21: AOTAG probe started
[ 7.046574] tegra_aotag tegra-aotag.21: nominal ft -- 105
[ 7.054825] tegra_aotag tegra-aotag.21: tall -- 76
[ 7.062396] tegra_aotag tegra-aotag.21: tiddq -- 1
[ 7.069928] tegra_aotag tegra-aotag.21: ten-count -- 16
[ 7.077892] tegra_aotag tegra-aotag.21: tsample -- 9
[ 7.085492] tegra_aotag tegra-aotag.21: pdiv -- 8
[ 7.092725] tegra_aotag tegra-aotag.21: nominal cp -- 25
[ 7.100484] tegra_aotag tegra-aotag.21: pdiv-ate -- 8
[ 7.107881] tegra_aotag tegra-aotag.21: tsamp-ate -- 39
[ 7.115375] tegra_aotag tegra-aotag.21: compensation A,B -- 10632,-67490
[ 7.124308] tegra_aotag tegra-aotag.21: sensor found :ID 0, Name: aotag0
[ 7.133182] tegra_aotag tegra-aotag.21: reading fuse value for sensor 0
[ 7.141880] tegra_aotag tegra-aotag.21: base-cp:22a shifted-cp:1
[ 7.149876] tegra_aotag tegra-aotag.21: base-ft:4b8 shifted-ft:fffffff5
[ 7.158416] tegra_aotag tegra-aotag.21: actual_aotag_cp 255, ft 995
[ 7.166544] tegra_aotag tegra-aotag.21: - Tsens calib value - 0x3ae5d27
[ 7.174959] tegra_aotag tegra-aotag.21: CPmask 1fff FTmask 3ffe000
[ 7.182871] tegra_aotag tegra-aotag.21: Tsense calib CP - 0x1d27
[ 7.190533] tegra_aotag tegra-aotag.21: Tsense Actual CP d.34727
[ 7.198093] tegra_aotag tegra-aotag.21: Tsense calib FT - 0x1d72
[ 7.205577] tegra_aotag tegra-aotag.21: Tsense Actual FT d.38002
[ 7.212979] tegra_aotag tegra-aotag.21: delta ts 3275, temp 740
[ 7.220203] tegra_aotag tegra-aotag.21: thermA-852, thermB--813
[ 7.227366] tegra_aotag tegra-aotag.21: Registering sensor 0
[ 7.234252] tegra_aotag tegra-aotag.21: Bound to TZ : ID 0
[ 7.240929] tegra_aotag tegra-aotag.21: shutdown temperature - 55
[ 7.248217] tegra_aotag tegra-aotag.21: AOTAG EN 60
[ 7.254303] tegra_aotag tegra-aotag.21: Probe done [SUCCESS]:0
[ 7.261940] md: raid0 personality registered for level 0
[ 7.268825] device-mapper: uevent: version 1.0.3
[ 7.275136] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 7.286848] Tegra210 cpuidle driver
[ 7.293242] sdhci: Secure Digital Host Controller Interface driver
[ 7.300987] sdhci: Copyright(c) Pierre Ossman
[ 7.306881] sdhci-pltfm: SDHCI platform and OF driver helper
[ 7.314553] mmc0: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[ 7.328440] sdhci-tegra sdhci-tegra.3: Parent select= pll_p rate=408000000
[ 7.337151] sdhci-tegra sdhci-tegra.3: Parent select= pll_c4_out2 rate=199680000
[ 7.348935] sdhci-tegra sdhci-tegra.3: Speedo value 1992
[ 7.356134] sdhci-tegra sdhci-tegra.3: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[ 7.368946] regulator_get() failed for (sdhci-tegra.3,vqmmc), -19
[ 7.377117] mmc0: no vqmmc regulator found
[ 7.383306] regulator_get() failed for (sdhci-tegra.3,vmmc), -19
[ 7.391468] mmc0: no vmmc regulator found
[ 7.430258] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA
[ 7.442488] mmc1: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[ 7.457902] sdhci-tegra sdhci-tegra.1: Parent select= pll_p rate=408000000
[ 7.468284] sdhci-tegra sdhci-tegra.1: Speedo value 1992
[ 7.476172] sdhci-tegra sdhci-tegra.1: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[ 7.490739] regulator_get() failed for (sdhci-tegra.1,vqmmc), -19
[ 7.499379] mmc1: no vqmmc regulator found
[ 7.505985] regulator_get() failed for (sdhci-tegra.1,vmmc), -19
[ 7.514540] mmc1: no vmmc regulator found
[ 7.560262] mmc1: SDHCI controller on sdhci-tegra.1 [sdhci-tegra.1] using ADMA
[ 7.573722] mmc2: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[ 7.589371] sdhci-tegra sdhci-tegra.0: Parent select= pll_p rate=408000000
[ 7.599857] sdhci-tegra sdhci-tegra.0: Speedo value 1992
[ 7.607818] sdhci-tegra sdhci-tegra.0: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[ 7.621976] regulator_get() failed for (sdhci-tegra.0,vqmmc), -19
[ 7.630700] mmc2: no vqmmc regulator found
[ 7.637368] regulator_get() failed for (sdhci-tegra.0,vmmc), -19
[ 7.646014] mmc0: BKOPS_EN bit is not set
[ 7.646024] mmc2: no vmmc regulator found
[ 7.680265] mmc2: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA
[ 7.692582] gpio wake35 for gpio=201
[ 7.702693] tegra-se tegra21-se: tegra_se_probe: complete
[ 7.711148] hidraw: raw HID events driver (C) Jiri Kosina
[ 7.721431] usbcore: registered new interface driver usbhid
[ 7.729425] usbhid: USB HID core driver
[ 7.735659] tegra_bootloader_debug: Created tegra_bootloader directory
[ 7.744602] tegra_bootloader_debug: Created sysfs interface tegra_bootloader_verify_regs in tegra_bootloader directory
[ 7.760008] tegra_bootloader_debug: Created sysfs interface tegra_bootloader_prof in tegra_bootloader directory
[ 7.775272] nvadsp 702ef000.adsp: in probe()...
[ 7.783024] nvadsp 702ef000.adsp: AMC/ARAM initialized.
[ 7.790730] nvadsp 702ef000.adsp: nvadsp_app_module_probe
[ 7.797438] mmc0: tap value and tuning window after hw tuning completion ...
[ 7.797445] mmc0: tuning_window[0]: 0x9fffffff
[ 7.797451] mmc0: tuning_window[1]: 0x7fffffff
[ 7.797456] mmc0: tuning_window[2]: 0xfffffffe
[ 7.797460] mmc0: tuning_window[3]: 0x7ffffff9
[ 7.797465] mmc0: tuning_window[4]: 0x0
[ 7.797470] mmc0: tuning_window[5]: 0x0
[ 7.797474] mmc0: tuning_window[6]: 0x0
[ 7.797478] mmc0: tuning_window[7]: 0x0
[ 7.797482] sdhci: Tap value: 46 | Trim value: 8
[ 7.797486] sdhci: SDMMC Interrupt status: 0x00040000
[ 7.798063] mmc0: switch to HS400 mode is successful
[ 7.802066] mmc0: new HS400 MMC card at address 0001
[ 7.802530] mmcblk0: mmc0:0001 016G32 14.6 GiB
[ 7.802746] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB
[ 7.803969] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18
[ 7.833294] mmc1: queuing unknown CIS tuple 0x80 (5 bytes)
[ 7.916264] tegra_throttle : init passed
[ 7.923512] cpu-tegra: init EDP limit: 1224 MHz
[ 7.930117] pll_x: not ready for dynamic ramp to 614400000
[ 7.937221] pll_x: not ready for dynamic ramp to 614400000
[ 7.949432] soctherm: skipping sensor 4 programming
[ 7.956037] soctherm: skipping sensor 5 programming
[ 7.996614] usbcore: registered new interface driver snd-usb-audio
[ 8.004610] No Device Node present for smmu client: snd-soc-dummy !!
[ 8.012636] No Device Node present for smmu client: snd-soc-dummy !!
[ 8.021047] No Device Node present for smmu client: snd-soc-dummy !!
[ 8.029107] No Device Node present for smmu client: snd-soc-dummy !!
[ 8.029431] mmc1: tap value and tuning window after hw tuning completion ...
[ 8.029439] mmc1: tuning_window[0]: 0xe3ffffff
[ 8.029444] mmc1: tuning_window[1]: 0x7fffffff
[ 8.029450] mmc1: tuning_window[2]: 0xfffffffc
[ 8.029454] mmc1: tuning_window[3]: 0x7fffffcf
[ 8.029459] mmc1: tuning_window[4]: 0x0
[ 8.029464] mmc1: tuning_window[5]: 0x0
[ 8.029468] mmc1: tuning_window[6]: 0x0
[ 8.029473] mmc1: tuning_window[7]: 0x0
[ 8.029477] sdhci: Tap value: 45 | Trim value: 8
[ 8.029481] sdhci: SDMMC Interrupt status: 0x00040000
[ 8.034567] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 8.034613] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[ 8.121034] Codec driver version 0.4 alsa 1.0.25
[ 8.131851] tegra-i2c 7000c000.i2c: no acknowledge from address 0x1b
[ 8.139800] rt5659 0-001b: Device with ID register ffffffc0 is not rt5659
[ 8.165222] tegra210-i2s tegra210-i2s.0: Missing prop fsync-width for I2S0
[ 8.174947] tegra210-i2s tegra210-i2s.2: Missing prop fsync-width for I2S2
[ 8.183743] tegra210-i2s tegra210-i2s.3: Missing prop fsync-width for I2S3
[ 8.192672] tegra210-i2s tegra210-i2s.4: Missing prop fsync-width for I2S4
[ 8.210065] OPE platform probe
[ 8.214906] OPE platform probe successful
[ 8.220455] OPE platform probe
[ 8.225313] OPE platform probe successful
[ 8.231151] tegra210_adsp_audio_platform_probe: platform probe started
[ 8.240889] tegra210-adsp adsp_audio.3: Default param-type to BYTE for mp3-dec1
[ 8.251622] tegra210-adsp adsp_audio.3: Default param-type to BYTE for spkprot
[ 8.262842] tegra210-adsp adsp_audio.3: Default param-type to BYTE for src
[ 8.272128] tegra210-adsp adsp_audio.3: Default param-type to BYTE for aac-dec1
[ 8.284046] tegra210_adsp_audio_platform_probe probe successfull.
[ 8.296828] tegra-snd-t210ref-mobile-rt565x sound.18: ASoC: CODEC (null) not registered
[ 8.311713] tegra-snd-t210ref-mobile-rt565x sound.18: snd_soc_register_card failed (-517)
[ 8.324695] platform sound.18: Driver tegra-snd-t210ref-mobile-rt565x requests probe deferral
[ 8.339198] GACT probability NOT on
[ 8.345117] Mirror/redirect action on
[ 8.351140] u32 classifier
[ 8.356195] Actions configured
[ 8.362018] Netfilter messages via NETLINK v0.30.
[ 8.369286] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 8.378400] ctnetlink v0.93: registering with nfnetlink.
[ 8.386423] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 8.396081] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 8.405092] xt_time: kernel timezone is -0000
[ 8.412305] ipip: IPv4 over IPv4 tunneling driver
[ 8.420313] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.428499] arp_tables: (C) 2002 David S. Miller
[ 8.435756] TCP: cubic registered
[ 8.441568] Initializing XFRM netlink socket
[ 8.448886] NET: Registered protocol family 10
[ 8.456970] mip6: Mobile IPv6
[ 8.462418] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.470522] sit: IPv6 over IPv4 tunneling driver
[ 8.478755] NET: Registered protocol family 17
[ 8.485595] NET: Registered protocol family 15
[ 8.492249] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 8.500379] Bluetooth: HIDP socket layer initialized
[ 8.507458] NET: Registered protocol family 35
[ 8.514026] Key type dns_resolver registered
[ 8.520342] NET: Registered protocol family 41
[ 8.529505] Registering SWP/SWPB emulation handler
[ 8.588830] isp isp.0: initialized
[ 8.596049] isp isp.1: initialized
[ 8.602046] vdd_gpu: disabling
[ 8.607240] en-vdd-cam-1v2: disabling
[ 8.613020] en-vdd-cam-hv-2v8: disabling
[ 8.618957] en-vdd-disp-1v8: disabling
[ 8.624686] en-mdm-pwr-3v7: disabling
[ 8.630270] en-vdd-disp-3v3: disabling
[ 8.635901] en-vdd-ts-hv-3v3: disabling
[ 8.641600] en-vdd-ts-1v8: disabling
[ 8.646973] usb-vbus3: disabling
[ 8.651823] usb-vbus1: disabling
[ 8.656610] vdd-fan: disabling
[ 8.667562] vdd-disp-3v0: disabling
[ 8.672594] snsr_pm: disabling
[ 8.677089] aux-3v3: disabling
[ 8.681531] en-vdd-cam: disabling
[ 8.686374] en-vdd-sd: disabling
[ 8.695881] lcd-bl-en: disabling
[ 8.700429] max77620-gpio7: disabling
[ 8.717037] vdd-cpu-fixed: disabling
[ 8.721909] regulator-dummy: disabling
[ 8.728378] tegra-snd-t210ref-mobile-rt565x: probe of sound.18 failed with error -16
[ 8.740182] gpio wake24 for gpio=189
[ 8.745275] gpio wake27 for gpio=192
[ 8.750325] gpio wake25 for gpio=190
[ 8.755493] input: gpio-keys as /devices/platform/gpio-keys.39/input/input0
[ 8.780787] max77620-rtc max77620-rtc.1: setting system clock to 2016-04-29 00:59:34 UTC (1461891574)
[ 8.793790] [dram-timers] DRAM derating cdev registered.
[ 8.800822] Disable partitions left on by BL
[ 8.806766] sata
[ 8.810745] disb
[ 8.814586] Disabling clocks left on by bootloader:
[ 8.821157] audio2_dmic
[ 8.825599] audio1_dmic
[ 8.829989] audio0_dmic
[ 8.834357] audio_2x
[ 8.838420] audio
[ 8.842222] audio4
[ 8.846062] audio3
[ 8.849873] audio2
[ 8.853684] audio1
[ 8.857439] audio0
[ 8.861249] entropy
[ 8.865024] dsi2-fixed
[ 8.868959] dsi1-fixed
[ 8.872863] sdmmc4_ddr
[ 8.876649] sdmmc1_ddr
[ 8.880492] sor1_src
[ 8.884117] cclk_lp
[ 8.888557] tegra_cl_dvfs 70110000.dfll-ovr: DT data retrieved successfully
[ 8.896915] tune_cpu_trimmers: init soctherm cpu zone LOW
[ 8.903587] tegra_cl_dvfs_init_cdev: cpu_cold cooling device registered
[ 8.911474] tegra_cl_dvfs_init_cdev: cpu_hot cooling device registered
[ 8.911865] Tegra CPU DFLL is initialized with use_dfll = 1
[ 8.912079] tegra_dvfs: 0.vdd-cpu-rail-ovr connected to regulator
[ 8.933275] tegra_dvfs: 4.vdd-core-rail-max77620 connected to regulator
[ 8.941453] tegra_dvfs: 1.vdd-gpu-rail-ovr connected to regulator
[ 8.949393] CPU rate: 614 MHz
[ 8.953554] last reset is due to power on reset
[ 8.953554]
[ 8.961227] KERNEL: PMC reset status reg: 0x0
[ 8.967125] tegra_actmon.emc: Completed initialization (0)
[ 8.974087] tegra_actmon.avp: Completed initialization (0)
[ 9.226940] tegra dvfs: tegra sysfs cap interface is initialized
[ 9.234224] tegra dvfs: tegra sysfs gpu interface is initialized
[ 9.242808] ALSA device list:
[ 9.246514] #0: HDA NVIDIA Tegra at 0x70038000 irq 113
[ 9.252833] md: Waiting for all devices to be available before autodetect
[ 9.260572] md: If you don't use raid, use raid=noautodetect
[ 9.267443] md: Autodetecting RAID arrays.
[ 9.272448] md: Scanned 0 and added 0 devices.
[ 9.277790] md: autorun ...
[ 9.281502] md: ... autorun DONE.
[ 9.286875] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[ 9.297808] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[ 9.352856] EXT4-fs (mmcblk0p1): 5 orphan inodes deleted
[ 9.359154] EXT4-fs (mmcblk0p1): recovery complete
[ 9.371988] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[ 9.382021] VFS: Mounted root (ext4 filesystem) on device 179:1.
[ 9.391166] devtmpfs: mounted
[ 9.395239] Freeing unused kernel memory: 428K (ffffffc001065000 - ffffffc0010d0000)
[ 9.405042] Freeing alternatives memory: 52K (ffffffc0010d1000 - ffffffc0010de000)
Mount failed for selinuxfs on /sys/fs/selinux: No such file or directory
[ 9.551879] init: plymouth-upstart-bridge main process (128) terminated with status 1
[ 9.562288] init: plymouth-upstart-bridge main process ended, respawning
[ 9.586087] init: plymouth-upstart-bridge main process (138) terminated with status 1
[ 9.596510] init: plymouth-upstart-bridge main process ended, respawning
[ 9.605139] init: ureadahead main process (131) terminated with status 5
[ 9.627237] init: plymouth-upstart-bridge main process (141) terminated with status 1
[ 9.637663] init: plymouth-upstart-bridge main process ended, respawning
* Starting Mount filesystems on boot [ OK ]
* Starting Signal sysvinit that the rootfs is mounted [ OK ]
* Starting Clean /tmp directory [ OK ]
* Starting Populate and link to /run filesystem [ OK ]
* Stopping Populate and link to /run filesystem [ OK ]
* Stopping Track if upstart is running in a container [ OK ]
* Stopping Clean /tmp directory [ OK ]
* Starting Initialize or finalize resolvconf [ OK ]
* Starting set console keymap [ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
* Starting Signal sysvinit that virtual filesystems are mounted [ OK ]
* Starting Bridge udev events into upstart [ OK ]
* Stopping set console keymap [ OK ]
* Starting Signal sysvinit that local filesystems are mounted [ OK ]
* Starting Signal sysvinit that remote filesystems are mounted [ OK ]
* Starting device node and kernel event manager [ OK ]
* Starting NFSv4 id <-> name mapper [ OK ]
* Starting flush early job output to logs [ OK ]
* Starting D-Bus system message bus [ OK ]
* Stopping Mount filesystems on boot [ OK ]
* Starting NVIDIA specific init script [ OK ]
* Starting load modules from /etc/modules [ OK ]
* Starting cold plug devices [ OK ]
* Starting log initial device creation [ OK ]
* Stopping flush early job output to logs [ OK ]
* Stopping load modules from /etc/modules [ OK ]
* Starting SystemD login management service [ OK ]
* Stopping NVIDIA specific init script [ OK ]
* Starting bluetooth daemon [ OK ]
* Stopping rpcsec_gss daemon [ OK ]
* Stopping NVIDIA specific first-boot script [ OK ]
* Starting system logging daemon [ OK ]
* Starting mDNS/DNS-SD daemon [ OK ]
* Starting Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
* Stopping NVIDIA bluetooth/wifi init script [ OK ]
* Stopping Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
* Starting set console font [ OK ]
* Stopping set console font [ OK ]
* Starting userspace bootsplash [ OK ]
* Stopping userspace bootsplash [ OK ]
* Starting Send an event to indicate plymouth is up [ OK ]
* Stopping Send an event to indicate plymouth is up [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device [ OK ]
* Starting configure network device [ OK ]
* Starting configure network device [ OK ]
* Starting configure network device [ OK ]
* Starting configure network device [ OK ]
* Starting Mount network filesystems [ OK ]
* Starting Upstart job to start rpcbind on boot only [ OK ]
* Starting Failsafe Boot Delay [ OK ]
* Stopping Upstart job to start rpcbind on boot only [ OK ]
* Stopping cold plug devices [ OK ]
* Stopping log initial device creation [ OK ]
* Stopping NVIDIA bluetooth/wifi init script [ OK ]
* Starting configure network device security [ OK ]
* Starting enable remaining boot-time encrypted block devices [ OK ]
* Starting configure network device [ OK ]
* Stopping Failsafe Boot Delay [ OK ]
* Starting RPC portmapper replacement [ OK ]
* Starting System V initialisation compatibility [ OK ]
* Starting nvcamera daemon [ OK ]
* Starting modem connection manager [ OK ]
* Starting configure network device security [ OK ]
* Starting configure virtual network devices [ OK ]
* Starting early crypto disks... [ OK ]
* Stopping Mount network filesystems [ OK ]
* Starting NSM status monitor [ OK ]
* Setting up X socket directories... [ OK ]
* Starting network connection manager [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device [ OK ]
* Stopping System V initialisation compatibility [ OK ]
* Starting configure network device security [ OK ]
* Starting configure network device [ OK ]
* speech-dispatcher disabled; edit /etc/default/speech-dispatcher
* Starting System V runlevel compatibility [ OK ]
* Starting Restore Sound Card State [ OK ]
* Starting regular background program processing daemon [ OK ]
* Starting anac(h)ronistic cron [ OK ]
* Starting save kernel messages [ OK ]
* Starting Restore Sound Card State [fail]
* Stopping save kernel messages [ OK ]
* Starting NTP server ntpd * Stopping anac(h)ronistic cron [ OK ]
[ OK ]
saned disabled; edit /etc/default/saned
* Stopping System V runlevel compatibility [ OK ]
Ubuntu 14.04.1 LTS tegra-ubuntu ttyS0
tegra-ubuntu login: ubuntu (automatic login)
Last login: Fri Apr 29 00:33:33 UTC 2016 on ttyS0
Welcome to Ubuntu 14.04.1 LTS (GNU/Linux 3.10.67-gbaaa7aa-dirty aarch64)
* Documentation: https://help.ubuntu.com/
505 packages can be updated.
247 updates are security updates.
ubuntu@tegra-ubuntu:~$