Jetson TX1 Boot Log

From RidgeRun Developer Wiki
Baudrate set to: 115200
Port Settings are: 8NC0S0
Port Device set to: /dev/ttyUSB0
Baudrate set to: 115200
Port Settings are: 8NC0S0
[0000.736] [TegraBoot] (version 23.00.2015.14-mobile-3a15407d)
[0000.742] Processing in cold boot mode Bootloader 2
[0000.746] A01 Bootrom Patch rev = 31
[0000.750] Power-up reason: on button
[0000.753] No Battery Present
[0000.756] Platform has Ddr4 type ram
[0000.759] max77620 disabling SD1 Remote Sense
[0000.764] Setting Ddr voltage to 1125mv
[0000.768] Serial Number of Pmic Max77663: 0x1004a4
[0000.776] Entering ramdump check
[0000.779] Get RamDumpCarveOut = 0x0
[0000.782] RamDumpCarveOut=0x0,  RamDumperFlag=0xe59ff3f8
[0000.787] Last reboot was clean, booting normally!
[0000.792] Sdram initialization is successful 
[0000.796] SecureOs Carveout Base=0xff800000 Size=0x00800000
[0000.801] GSC1 Carveout Base=0xff700000 Size=0x00100000
[0000.827] GSC2 Carveout Base=0xff600000 Size=0x00100000
[0000.853] GSC3 Carveout Base=0xff500000 Size=0x00100000
[0000.858] GSC4 Carveout Base=0xff400000 Size=0x00100000
[0000.863] GSC5 Carveout Base=0xff300000 Size=0x00100000
[0000.868] BpmpFw Carveout Base=0xff2c0000 Size=0x00040000
[0000.874] Lp0 Carveout Base=0xff2bf000 Size=0x00001000
[0000.889] RamDump Carveout Base=0xff23f000 Size=0x00080000
[0000.894] Platform-DebugCarveout: 0
[0000.898] Nck Carveout Base=0xff03f000 Size=0x00200000
[0000.938] Using GPT Primary to query partitions 
[0000.943] Loading Tboot-CPU binary
[0000.992] Verifying bootloader in OdmNonSecureSBK mode
[0001.002] Bootloader load address is 0xa0000000,                            entry address is 0xa0000258
[0001.011] Bootloader downloaded successfully.
[0001.016] Downloaded Tboot-CPU binary to 0xa0000258
[0001.021] MAX77620_GPIO1 Configured.
[0001.025] MAX77620_GPIO5 Configured.
[0001.028] CPU power rail is up
[0001.031] CPU clock enabled
[0001.035] Performing RAM repair
[0001.038] Updating A64 Warmreset Address to 0xa00002e9
[0001.055] Bootloader DTB Load Address: 0x83000000
[0001.071] Kernel DTB Load Address: 0x83080000
[0001.076] Loading cboot binary
[0001.170] Verifying bootloader in OdmNonSecureSBK mode
[0001.264] Bootloader load address is 0x8010fda8,                            entry address is 0x80110000
[0001.273] Bootloader downloaded successfully.
[0001.277] GPT: Partition NOT found ! 
[0001.281] Find Partition via GPT Failed
[0001.284] function NvTbootGetBinaryOffsets: 0x845208 error
[0001.289] Error in NvTbootLoadBinary: 0x845208 !
[0001.294] Next binary entry address: 0x80110000 
[0001.298] BoardId: 2180
[0001.325] NvTbootI2cWrite(): error code 0x00045100 Error while starting write transaction
[0001.332] NvTbootI2cDeviceRead(): error code 0x00045001 Error while sending the offset to slave
[0001.341] NvTbootI2c: Read failed for slave 0xa2, offset 0x00 with error code 0x00045001
[0001.349] Display board id read failed 
[0001.353] dram memory type is 3
[0001.357] WB0 init successful
[0001.383] Bpmp FW successfully loaded
[0001.386] Set NvDecSticky Bits
[0001.389] GSC1 address : ff700000
[0001.393] GSC2 address : ff600000
[0001.397] GSC3 address : ff500000
[0001.401] GSC4 address : ff400000
[0001.404] GSC5 address : ff300000
[0001.408] GSC MC Settings done
[0001.411] TOS old plaintext Image length 61440
[0001.417] *** Secure OS image signature not verified ***
[0001.423] Loading and Validation of Secure OS Successful
[0001.428] NvTbootPackSdramParams: start. 
[0001.433] NvTbootPackSdramParams: done. 
[0001.436] Tegraboot started after 126107 us
[0001.440] Basic modules init took 942242 us
[0001.444] Sec Bootdevice Read Time = 194 ms, Read Size = 8459 KB
[0001.450] Next stage binary read took 12293 us
[0001.454] Carveout took 251766 us
[0001.458] CPU initialization took 138946 us
[0001.462] Total time taken by TegraBoot 1345247 us

[0001.466] Starting CPU & Halting co-processor 

64b[0001.602] LPDDR4 Training: Number of tables = 10
[0001.606] EMC Training (SRC-freq: 204000; DST-freq: 408000)
[0001.612] EMC Training Successful
[0001.615] EMC Training (SRC-freq: 204000; DST-freq: 665600)
[0001.621] EMC Training Successful
[0001.624] EMC Training (SRC-freq: 204000; DST-freq: 800000)
[0001.636] EMC Training Successful
[0001.639] EMC Training (SRC-freq: 204000; DST-freq: 1065600)
[0001.661] EMC Training Successful
[0001.664] EMC Training (SRC-freq: 204000; DST-freq: 1331200)
[0001.686] EMC Training Successful
[0001.689] EMC Training (SRC-freq: 204000; DST-freq: 1600000)
[0001.709] EMC Training Successful
[0001.712] Switching to 800000 KHz Success
[0001.745] LPDDR4 Training: Number of tables = 10


U-Boot 2015.07-rc2 (Apr 28 2016 - 19:24:09 -0600)

TEGRA210
Model: NVIDIA P2371-2180
DRAM:  4 GiB
MMC:   Tegra SD/MMC: 0, Tegra SD/MMC: 1
*** Warning - bad CRC, using default environment

tegra-pcie: PCI regions:
tegra-pcie:   I/O: 0x0000000012000000-0x0000000012010000
tegra-pcie:   non-prefetchable memory: 0x0000000013000000-0x0000000020000000
tegra-pcie:   prefetchable memory: 0x0000000020000000-0x0000000040000000
tegra-pcie: 4x1, 1x1 configuration
tegra-pcie: probing port 0, using 4 lanes
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, retrying
tegra-pcie: link 0 down, ignoring
tegra-pcie: probing port 1, using 1 lanes
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, retrying
tegra-pcie: link 1 down, ignoring
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0 
MMC: no card present
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:1...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
948 bytes read in 299 ms (2.9 KiB/s)
p2371-2180 eMMC boot options
1:	primary kernel
Enter choice: 1:	primary kernel
Retrieving file: /boot/Image
18951520 bytes read in 499 ms (36.2 MiB/s)
append: fbcon=map:0 console=tty0 console=ttyS0,115200n8 androidboot.modem=none androidboot.serialno=P2180A00P00940c003fd androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootreason=pmc:software_reset,pmic:0x0 root=/dev/mmcblk0p1 rw rootwait
Retrieving file: /boot/tegra210-jetson-tx1-p2597-2180-a01-devkit.dtb
250527 bytes read in 71 ms (3.4 MiB/s)
## Flattened Device Tree blob at 82000000
   Booting using the fdt blob at 0x82000000
   reserving fdt memory region: addr=80000000 size=20000
   Using Device Tree in place at 0000000082000000, end 000000008204029e

Starting kernel ...

[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 3.10.67-gbaaa7aa-dirty (dsoto@dsoto-pc) (gcc version 5.3.1 20160113 (Linaro GCC 5.3-2016.02) ) #1 SMP PREEMPT Mon Apr 11 12:54:42 CST 2016
[    0.000000] CPU: Cortex A57 Processor [411fd071] revision 1
[    0.000000] alternative: enabling workaround for ARM erratum 832075
[    0.000000] Machine: jetson_tx1
[    0.000000] bootconsole [earlycon0] enabled
[    0.000000] Tegra reserved memory:
[    0.000000] LP0:                    ff2bf000 - ff2bffff
[    0.000000] Bootloader framebuffer: 00000000 - 00000000
[    0.000000] Bootloader framebuffer2: 00000000 - 00000000
[    0.000000] Framebuffer:            f6200000 - fa9fffff
[    0.000000] 2nd Framebuffer:        faa00000 - ff1fffff
[    0.000000] Carveout:               00000000 - 00000000
[    0.000000] Vpr:                    00000000 - 0b9fffff
[    0.000000] Tsec:                   00000000 - 00000000
[    0.000000] Bootloader Debug Data:  00000000 - 00000000
[    0.000000] Nvdumper:               ff23f000 - ff23ffff
[    0.000000] cma: CMA: reserved 188 MiB at ea400000
[    0.000000] cma: CMA: reserved 16 MiB at e9400000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv0.2 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] DTS File Name: arch/arm64/boot/dts/tegra210-jetson-tx1-p2597-2180-a01-devkit.dts
[    0.000000] DTB Build time: Apr 11 2016 13:11:36
[    0.000000] Tegra21: Speedo/IDDQ fuse revision 4
[    0.000000] Tegra21: CPU Speedo ID 7, Soc Speedo ID 0, Gpu Speedo ID 2
[    0.000000] Tegra21: CPU Process ID 0, Soc Process ID 1, Gpu Process ID 0
[    0.000000] Tegra21: CPU Speedo value 2067, Soc Speedo value 1992, Gpu Speedo value 2076
[    0.000000] Tegra21: CPU IDDQ 2056, Soc IDDQ 2336, Gpu IDDQ 2870
[    0.000000] Tegra Revision: A02 SKU: 0x17 CPU Process: 0 Core Process: 1
[    0.000000] tegra: PLLP fixed rate: 408000000
[    0.000000] pll_u: boot with h/w control already set
[    0.000000] pll_x boot misc1 0x0 : expected 0x20
[    0.000000]  (comparison mask = 0xffffff)
[    0.000000] pll_c4 rates match 204000000 max sdmmc: vco=998400000 out0=998400000 out3=998400000
[    0.000000] Lowering vic03 maximum rate from 1000000000 to 627200000
[    0.000000] Lowering nvjpg maximum rate from 1000000000 to 627200000
[    0.000000] Lowering se maximum rate from 1000000000 to 627200000
[    0.000000] Lowering tsecb maximum rate from 1000000000 to 627200000
[    0.000000] Lowering msenc maximum rate from 1000000000 to 716800000
[    0.000000] Lowering nvdec maximum rate from 1000000000 to 716800000
[    0.000000] Lowering vi maximum rate from 1000000000 to 793600000
[    0.000000] Lowering isp maximum rate from 1000000000 to 793600000
[    0.000000] Lowering adsp_bus maximum rate from 1200000000 to 844800000
[    0.000000] Lowering sbus maximum rate from 600000000 to 408000000
[    0.000000] Lowering host1x maximum rate from 600000000 to 408000000
[    0.000000] Lowering pll_c maximum rate from 1200000000 to 1130000000
[    0.000000] Lowering pll_c2 maximum rate from 1200000000 to 1130000000
[    0.000000] Lowering pll_c3 maximum rate from 1200000000 to 1130000000
[    0.000000] Lowering pll_d2 maximum rate from 1500000000 to 1130000000
[    0.000000] Lowering pll_dp maximum rate from 1500000000 to 1130000000
[    0.000000] Lowering sor0 maximum rate from 600000000 to 540000000
[    0.000000] Lowering sor1 maximum rate from 600000000 to 594000000
[    0.000000] Lowering dmic1 maximum rate from 12288000 to 12190000
[    0.000000] Lowering dmic2 maximum rate from 12288000 to 12190000
[    0.000000] Lowering dmic3 maximum rate from 12288000 to 12190000
[    0.000000] Lowering hda maximum rate from 102000000 to 51000000
[    0.000000] Lowering sdmmc2 maximum rate from 266000000 to 204000000
[    0.000000] Lowering qspi maximum rate from 133000000 to 116600000
[    0.000000] Lowering gbus maximum rate from 1300000000 to 998400000
[    0.000000] Lowering cpu_g maximum rate from 3000000000 to 1734000000
[    0.000000] Lowering cpu_lp maximum rate from 1350000000 to 1132800000
[    0.000000] tegra dvfs: vdd_cpu: nominal 1226mV, offset 708000uV, step 19200uV, scaling enabled
[    0.000000] tegra dvfs: vdd_core: nominal 1075mV, offset 0uV, step 12500uV, scaling enabled
[    0.000000] tegra dvfs: vdd_gpu: nominal 1100mV, offset 710000uV, step 10000uV, scaling enabled
[    0.000000] tegra_powergate_init: DONE
[    0.000000] tegra21_plle_clk_enable: pll_e is already enabled
[    0.000000] PERCPU: Embedded 13 pages/cpu @ffffffc03feb3000 s21504 r8192 d23552 u53248
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 993840
[    0.000000] Kernel command line: fbcon=map:0 console=tty0 console=ttyS0,115200n8 androidboot.modem=none androidboot.serialno=P2180A00P00940c003fd androidboot.security=non-secure tegraid=21.1.2.0.0 ddr_die=2048M@2048M ddr_die=2048M@4096M section=256M memtype=0 vpr_resize usb_port_owner_info=0 lane_owner_info=0 emc_max_dvfs=0 touch_id=0@63 video=tegrafb no_console_suspend=1 debug_uartport=lsport,0 earlyprintk=uart8250-32bit,0x70006000 maxcpus=4 usbcore.old_scheme_first=1 lp0_vec=0x1000@0xff2bf000 nvdumper_reserved=0xff23f000 core_edp_mv=1125 core_edp_ma=4000 gpt android.kerneltype=normal androidboot.touch_vendor_id=0 androidboot.touch_panel_id=63 androidboot.touch_feature=0 androidboot.bootreason=pmc:software_reset,pmic:0x0 root=/dev/mmcblk0p1 rw rootwait
[    0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[    0.000000] Memory: 1888MB 2048MB = 3936MB total
[    0.000000] Memory: 3736972k/3736972k available, 293492k reserved
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbbffff0000   (245759 MB)
[    0.000000]     vmemmap : 0xffffffbc01c00000 - 0xffffffbc05400000   (    56 MB)
[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc100000000   (  4096 MB)
[    0.000000]       .init : 0xffffffc001065000 - 0xffffffc0010d0400   (   429 kB)
[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc0010641c4   ( 16273 kB)
[    0.000000]       .data : 0xffffffc0010e4000 - 0xffffffc001292c40   (  1724 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000] NR_IRQS:960 nr_irqs:960 0
[    0.000000] the number of interrupt controllers found is 6
[    0.000000] Architected local timer running at 19.20MHz (phys).
[    0.000000] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
[    0.000000] Wake16 for irq=34
[    0.000000] Wake16 for irq=34
[    0.000000] Enabling wake16
[    0.000000] Console: colour dummy device 80x25
[    0.000000] console [tty0] enabled
[    0.016491] Calibrating delay loop (skipped), value calculated using timer frequency.. lpj=192000
[    0.025313] pid_max: default: 32768 minimum: 301
[    0.030018] Security Framework initialized
[    0.034044] Mount-cache hash table entries: 256
[    0.085685] Initializing cgroup subsys debug
[    0.087974] Initializing cgroup subsys freezer
[    0.092648] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[    0.140377] ftrace: Allocated trace_printk buffers
[    0.201165] Brought up 4 CPUs
[    0.202151] SMP: Total of 4 processors activated.
[    0.206851] alternatives: patching kernel code
[    0.214675] devtmpfs: initialized
[    0.232455] pinctrl core: initialized pinctrl subsystem
[    0.236074] regulator-dummy: ; Rail ON
[    0.244575] Initializing plugin-manager
[    0.246751] node /plugin-manager/p2180-1000-300@0 match with board 2180-1000-100
[    0.254281] NET: Registered protocol family 16
[    0.261314] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.267150] console [pstore-1] enabled
[    0.270025] ramoops: attached 0x200000@0xf6000000, ecc: 0/0
[    0.276033] I2C first dynamic bus number based on alias = 7
[    0.281199] cpuidle: using governor ladder
[    0.285179] cpuidle: using governor menu
[    0.289799] PMC: Setting PMIC interrupt active-low
[    0.294551] tegra-pmc device create success
[    0.298085] padctrl padctrl.0: Pad control driver tegra-pmc-padctrl registered
[    0.305219] Clear bootloader IO dpd settings
[    0.309448] PMC: configuring io pad defaults
[    0.313944] PMC: IO pad audio voltage is 1800000
[    0.318387] PMC: IO pad cam voltage is 1800000
[    0.322818] PMC: IO pad dbg voltage is 1800000
[    0.327226] PMC: IO pad dmic voltage is 1800000
[    0.331745] PMC: IO pad pex-ctrl voltage is 1800000
[    0.336587] PMC: IO pad spi voltage is 1800000
[    0.341018] PMC: IO pad uart voltage is 1800000
[    0.345513] PMC: IO pad bb voltage is 1800000
[    0.349845] PMC: IO pad audio-hv voltage is 1800000
[    0.354712] PMC: IO pad spi-hv voltage is 1800000
[    0.359380] PMC: IO pad gpio voltage is 1800000
[    0.363898] PMC: IO pad sdmmc3 voltage is 1800000
[    0.368475] PMC: IO pad pex-bias power is disable
[    0.373165] PMC: IO pad pex-clk1 power is disable
[    0.377832] PMC: IO pad pex-clk2 power is disable
[    0.382515] T210 pmc padctrl driver initialized
[    0.387079] T210 pmc config for bootrom command passed
[    0.393510] INFO: pinmux CLAMP_INPUTS_WHEN_TRISTATED: disabled
[    0.400329] clk_init_from_dt_table: clocks are set from t210-clk-init-table:clkinit-0
[    0.409586] tegra_smmu 70019000.iommu: Loaded Tegra IOMMU driver
[    0.413871] platform bpmp.15: domain=ffffffc0ff04d698 allocates as[0]=ffffffc0ff1040a8
[    0.421771] platform bpmp.15: IOVA linear map 0x00000000ff2c0000(40000)
[    0.428713] bpmp bpmp.15: bpmp_connect returned 0
[    0.433696] MC mapped MMIO address: 0xffffff800003a000
[    0.437989] MC0 mapped MMIO address: 0xffffff8000072000
[    0.443209] MC1 mapped MMIO address: 0xffffff8000098000
[    0.460290] tegra210-pinctrl 700008d4.pinmux: lookup the user state drive not found
[    0.466076] tegra210-pinctrl 700008d4.pinmux: Probed Tegra pinctrl driver
[    0.473409] GPIO chip tegra-gpio: created GPIO range 0->245 ==> 700008d4.pinmux PIN 0->245
[    0.481033] tegra-gpio 6000d000.gpio: Initialising GPIO state 0: name wlan-default
[    0.488579] gpiochip_add: registered GPIOs 0 to 255 on device: tegra-gpio
[    0.499020] Wake44 for irq=81
[    0.500042] Wake40 for irq=53
[    0.502944] Wake41 for irq=53
[    0.505889] Wake42 for irq=53
[    0.508835] Wake43 for irq=53
[    0.512459] platform 70006000.serial: domain=ffffffc0ff125298 allocates as[0]=ffffffc0ff104110
[    0.521697] platform sound.18: domain=ffffffc0ff125518 allocates as[0]=ffffffc0ff104178
[    0.531307] platform tegradc.1: domain=ffffffc0ff125918 allocates as[0]=ffffffc0ff1041e0
[    0.541405] platform tegradc.1: IOVA linear map 0x00000000f6200000(4800000)
[    0.550350] platform tegradc.1: IOVA linear map 0x00000000faa00000(4800000)
[    0.555502] platform tegradc.1: IOVA linear map 0x00000000ea400000(bc00000)
[    0.564778] platform gpu.0: domain=ffffffc0ff125a98 allocates as[0]=ffffffc0ff104248
[    0.570604] platform gpu.0: domain=ffffffc0ff125a98 allocates as[1]=ffffffc0ff1042b0
[    0.578295] platform gpu.0: domain=ffffffc0ff125a98 allocates as[2]=ffffffc0ff104318
[    0.586024] platform gpu.0: domain=ffffffc0ff125a98 allocates as[3]=ffffffc0ff104380
[    0.599190] platform sdhci-tegra.3: domain=ffffffc0ff192098 allocates as[0]=ffffffc0ff1043e8
[    0.606251] platform sdhci-tegra.0: domain=ffffffc0ff192298 allocates as[0]=ffffffc0ff104450
[    0.614435] Wake39 for irq=52
[    0.628377] gpio wake52 for gpio=61
[    0.630301] gpio wake8 for gpio=58
[    0.633304] gpio wake8 for gpio=58
[    0.638183] irq: no irq domain found for /soctherm@0x700E2000 !
[    0.642778] irq: no irq domain found for /soctherm@0x700E2000 !
[    0.648620] board_info: id:sku:fab:major:minor = 0x0884:0x03e8:0x00:0x00:0x00
[    0.655571] PMC dt information non-NULL tegra_init_suspend
[    0.668562] Loading EMC tables...
[    0.669987] tegra: Using EMC sequence '21021' for Rev. 7 tables
[    0.675822] tegra: emc: Derated table is valid.
[    0.680320] Lowering emc maximum rate from 1800000000 to 1600000000
[    0.686546] tegra: validated EMC DFS table
[    0.703520] swapper/0 isomgr_init(): iso emc max clk=1600000KHz
[    0.707457] swapper/0 isomgr_init(): max_iso_bw=11520000KB
[    1.969921] vdso: 2 pages (1 code, 1 data) at base ffffffc0010ea000
[    1.974260] vdso32: 2 pages (1 code, 1 data) at base ffffffc0010e9000
[    1.980670] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.987523] nvdumper: last reboot was unknown
[    1.991752] nvdumper: set_dirty_state 0x2badface
[    1.996866] Tegra restart notifier registered.
[    2.013561] bio: create slab <bio-0> at 0
[    2.017737] vdd-ac-bat: 5000 mV ; Rail ON
[    2.020033] vdd-cpu-fixed: 1000 mV ; Rail ON
[    2.024938] vgaarb: loaded
[    2.027104] SCSI subsystem initialized
[    2.030894] usbcore: registered new interface driver usbfs
[    2.035939] usbcore: registered new interface driver hub
[    2.041287] usbcore: registered new device driver usb
[    2.047000] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/icm20628@68
[    2.053241] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/ak8963@0d
[    2.060068] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/bmp280@77
[    2.066931] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/cm32180@48
[    2.073860] i2c i2c-0: of_i2c: modalias failure on /i2c@7000c000/iqs263@44
[    2.080764] gpio wake33 for gpio=188
[    2.085699] regulator_get() failed for (1-0074,vcc), -19
[    2.089535] pca953x 1-0074: no regulator found for vcc. Assuming vcc is always powered
[    2.098193] gpio wake21 for gpio=89
[    2.101127] gpiochip_add: registered GPIOs 1008 to 1023 on device: tca9539
[    2.108121] regulator_get() failed for (1-0077,vcc), -19
[    2.113042] pca953x 1-0077: no regulator found for vcc. Assuming vcc is always powered
[    2.121658] gpio wake36 for gpio=202
[    2.124634] gpiochip_add: registered GPIOs 992 to 1007 on device: tca9539
[    2.131907] i2c i2c-3: of_i2c: modalias failure on /i2c@7000c700/prod-settings
[    2.139648] max77620 4-003c: CID0: 0xa4
[    2.142343] max77620 4-003c: CID1: 0x04
[    2.146130] max77620 4-003c: CID2: 0x10
[    2.149942] max77620 4-003c: CID3: 0x59
[    2.153776] max77620 4-003c: CID4: 0x35
[    2.157569] max77620 4-003c: CID5: 0x80
[    2.161403] max77620 4-003c: MAX77620 PMIC OTP Version is 0x35
[    2.168800] max77620-pmic max77620-pmic: Consumer c2 does not have device name
[    2.174433] max77620-pmic max77620-pmic: Consumer c0 does not have device name
[    2.182610] vdd_core: 600 <--> 1400 mV at 1000 mV with ramp delay 27500 uV/us ; Rail ON
[    2.190394] vddio-ddr: at 1125 mV with ramp delay 27500 uV/us ; Rail ON
[    2.196705] vdd-pre-reg: 1350 mV with ramp delay 27500 uV/us ; Rail ON
[    2.203736] vdd-1v8: 1800 mV with ramp delay 27500 uV/us ; Rail ON
[    2.209526] avdd-sys: 1200 mV with ramp delay 100000 uV/us ; Rail ON
[    2.215117] avdd-sys: supplied by vdd-pre-reg
[    2.220102] vdd-pex: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[    2.225670] vdd-pex: supplied by vdd-pre-reg
[    2.230387] vddio-sdmmc1: 1800 <--> 3300 mV at 3300 mV with ramp delay 100000 uV/us ; Rail ON
[    2.238914] vdd-cam-hv: 2800 mV with ramp delay 100000 uV/us ; Rail OFF
[    2.245650] vdd-rtc: 850 mV with ramp delay 100000 uV/us ; Rail ON
[    2.251660] avdd-ts-hv: 3300 mV with ramp delay 100000 uV/us ; Rail OFF
[    2.258942] vdd-ts: 1800 mV with ramp delay 100000 uV/us ; Rail OFF
[    2.264740] vdd-gen-pll-edp: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[    2.270911] vdd-gen-pll-edp: supplied by vdd-pre-reg
[    2.276560] vdd-hdmi-dp: 1050 mV with ramp delay 100000 uV/us ; Rail ON
[    2.282431] vdd-hdmi-dp: supplied by vdd-pre-reg
[    2.287570] max77620-gpio max77620-gpio.0: Initialising GPIO state 1: name gpio_default
[    2.295057] gpiochip_add: registered GPIOs 984 to 991 on device: max77620-gpio
[    2.303367] max77620-gpio max77620-gpio.0: max77620 gpio successfully initialized
[    2.313416] max77620 4-003c: max77620 probe successfully
[    2.317584] Linux video capture interface: v2.00
[    2.321406] pps_core: LinuxPPS API ver. 1 registered
[    2.326275] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    2.335412] PTP clock support registered
[    2.341272] Advanced Linux Sound Architecture Driver Initialized.
[    2.345861] Bluetooth: Core ver 2.16
[    2.348965] NET: Registered protocol family 31
[    2.353369] Bluetooth: HCI device and connection manager initialized
[    2.359689] Bluetooth: HCI socket layer initialized
[    2.364552] Bluetooth: L2CAP socket layer initialized
[    2.369587] Bluetooth: SCO socket layer initialized
[    2.375931] vdd-3v3: 3300 mV ; Rail ON
[    2.379561] max77620-gpio7: 1050 mV ; Rail ON
[    2.382542] max77620-gpio7: supplied by vdd-gen-pll-edp
[    2.388046] lcd-bl-en: 1800 mV ; Rail ON
[    2.391907] en-vdd-sd: 3300 mV ; Rail OFF
[    2.395611] en-vdd-sd: supplied by vdd-3v3
[    2.399829] reg-fixed-sync-voltage 5.regulator: Consumer c1 does not have device name
[    2.407911] en-vdd-cam: 1800 mV ; Rail OFF
[    2.411569] en-vdd-cam: supplied by vdd-1v8
[    2.422582] vdd-sys-boost: 5000 mV ; Rail ON
[    2.425513] vdd-hdmi: 5000 mV ; Rail OFF
[    2.428815] vdd-hdmi: supplied by vdd-3v3
[    2.433095] aux-3v3: 3300 mV ; Rail ON
[    2.436735] snsr_pm: 3300 mV ; Rail ON
[    2.440981] vdd-disp-3v0: 3000 mV ; Rail ON
[    2.444970] vdd-fan: 5000 mV ; Rail OFF
[    2.448496] usb-vbus1: 5000 mV ; Rail OFF
[    2.452234] usb-vbus1: supplied by vdd-3v3
[    2.456574] usb-vbus3: 5000 mV ; Rail OFF
[    2.460289] usb-vbus3: supplied by vdd-3v3
[    2.464937] en-vdd-ts-1v8: 1800 mV ; Rail OFF
[    2.469261] en-vdd-ts-hv-3v3: 3300 mV ; Rail OFF
[    2.474000] en-vdd-disp-3v3: 3300 mV ; Rail ON
[    2.478247] en-mdm-pwr-3v7: ; Rail OFF
[    2.482138] en-vdd-disp-1v8: 1800 mV ; Rail ON
[    2.486393] en-vdd-cam-hv-2v8: ; Rail OFF
[    2.490079] rtl-5v0: ; Rail OFF
[    2.493232] en-usb-vbus2: ; Rail OFF
[    2.497058] en-vdd-cam-1v2: ; Rail OFF
[    2.501145] regulator-pwm 0.pwm-regulator: PWM request deferred
[    2.506088] platform 0.pwm-regulator: Driver regulator-pwm requests probe deferral
[    2.514304] vdd_gpu: applied init 1000000uV constraint
[    2.518732] vdd_gpu: 710 <--> 1320 mV at 1000 mV ; Rail OFF
[    2.526048] vdd_cpu: applied init 1000000uV constraint
[    2.529392] vdd_cpu: 708 <--> 1322 mV at 1000 mV normal ; Rail ON
[    2.538258] gpio wake34 for gpio=200
[    2.541497] extcon-gpio-states 1.extcon: Cable state 1
[    2.547098] Switching to clocksource arch_sys_counter
[    2.582420] No Device Node present for smmu client: tegra-carveouts !!
[    2.586984] No Device Node present for smmu client: tegra-carveouts !!
[    2.593643] nvmap_heap_init: nvmap_heap_init: created heap block cache
[    2.600438] No Device Node present for smmu client: tegra-carveouts !!
[    2.606490] dma_declare_coherent_resizable_cma_memory:278: resizable heap=vpr, base=0x0x00000000ea400000, size=0xbc00000
[    2.617330]  dma-vpr: heap size is not multiple of cma_chunk_size heap_info->num_chunks (6) rem_chunk_size(0x1c00000)
[    2.628082] cma: enabled page replacement for spfn=ea400, epfn=f6000
[    2.634219] dma_declare_coherent_resizable_cma_memory:325: resizable cma heap=vpr create successful
[    2.643055] nvmap_page_pool_init: Total RAM pages: 986467
[    2.648582] nvmap_page_pool_init: nvmap page pool size: 123308 pages (481 MB)
[    2.655785] nvmap_background_zero_thread: PP zeroing thread starting.
[    2.656036] misc nvmap: iram :dma coherent mem declare 0x0000000040001000,258048
[    2.656749] misc nvmap: created heap iram base 0x0000000040001000 size (252KiB)
[    2.657240] misc nvmap: created heap vpr base 0x00000000ea400000 size (192512KiB)
[    2.657615] nvmap:inner cache maint threshold=2097152
[    2.657616] No Device Node present for smmu client: tegra-carveouts !!
[    2.667693] Wake39 for irq=52
[    2.667807] tegra-otg tegra-otg: otg transceiver registered
[    2.668419] thermal thermal_zone0: Registering thermal zone thermal_zone0 for type AO-therm
[    2.669619] thermal thermal_zone1: Registering thermal zone thermal_zone1 for type CPU-therm
[    2.669991] thermal thermal_zone2: Registering thermal zone thermal_zone2 for type GPU-therm
[    2.670186] thermal thermal_zone3: Registering thermal zone thermal_zone3 for type PLL-therm
[    2.670376] thermal thermal_zone4: Registering thermal zone thermal_zone4 for type PMIC-Die
[    2.671540] thermal thermal_zone5: Registering thermal zone thermal_zone5 for type Tdiode_tegra
[    2.671785] thermal thermal_zone6: Registering thermal zone thermal_zone6 for type Tboard_tegra
[    2.672823] tegra21_plle_clk_enable: pll_e hw sequencer is already on
[    2.672846] t210_sata_uphy_pll_init: init sata uphy pll
[    2.672860] t210_sata_uphy_pll_init SATA uses SATA Lane
[    2.673186] tegra_xusb_padctl_phy_enable: pex uphy already enabled
[    2.674658] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sys is having fixed voltage 1800000
[    2.674755] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-uart is having fixed voltage 1800000
[    2.674849] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-audio is having fixed voltage 1800000
[    2.674948] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-cam is having fixed voltage 1800000
[    2.675060] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-pex-ctrl is having fixed voltage 1800000
[    2.675155] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc1 is having voltages: 1800000:3300000
[    2.675255] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc3 is having fixed voltage 1800000
[    2.675350] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc4 is having fixed voltage 1800000
[    2.675447] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-audio-hv is having fixed voltage 1800000
[    2.675540] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-debug is having fixed voltage 1800000
[    2.675649] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-dmic is having fixed voltage 1800000
[    2.675744] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-gpio is having fixed voltage 1800000
[    2.675845] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-spi is having fixed voltage 1800000
[    2.675938] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-spi-hv is having fixed voltage 1800000
[    2.676033] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-sdmmc2 is having fixed voltage 1800000
[    2.676142] tegra210-pmc-iopower pmc-iopower.20: Rail iopower-dp is having fixed voltage 1800000
[    2.676149] tegra210-pmc-iopower pmc-iopower.20: NO_IO_POWER setting 0x0
[    2.676464] NET: Registered protocol family 2
[    2.677260] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
[    2.677488] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[    2.677723] TCP: Hash tables configured (established 32768 bind 32768)
[    2.677821] TCP: reno registered
[    2.677832] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[    2.677875] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[    2.678206] NET: Registered protocol family 1
[    2.678601] RPC: Registered named UNIX socket transport module.
[    2.678604] RPC: Registered udp transport module.
[    2.678608] RPC: Registered tcp transport module.
[    2.678611] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    2.679076] tegra-fuse tegra-fuse: Fuse driver initialized succesfully
[    2.685872] host1x host1x: initialized
[    2.697409] NTFS driver 2.1.30 [Flags: R/O].
[    2.697690] fuse init (API version 7.22)
[    2.698115] msgmni has been set to 7706
[    2.699582] io scheduler noop registered (default)
[    2.699798] Tegra cpuquiet initialized: disabled
[    2.702276] tegra-pcie 1003000.pcie-controller: PCIE: Enable power rails
[    2.703324] tegra-pcie 1003000.pcie-controller: probing port 0, using 4 lanes and lane map as 0x14
[    2.705388] tegra-pcie 1003000.pcie-controller: probing port 1, using 1 lanes and lane map as 0x14
[    3.108404] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[    3.514295] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[    3.920352] tegra-pcie 1003000.pcie-controller: link 0 down, retrying
[    3.926827] tegra-pcie 1003000.pcie-controller: link 0 down, ignoring
[    4.333393] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[    4.743623] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[    5.153582] tegra-pcie 1003000.pcie-controller: link 1 down, retrying
[    5.160059] tegra-pcie 1003000.pcie-controller: link 1 down, ignoring
[    5.164571] tegra-pcie 1003000.pcie-controller: PCIE: no ports detected
[    5.171423] tegra-pcie 1003000.pcie-controller: PCIE: Disable power rails
[    5.180386] tsec tsec: initialized
[    5.183123] tsec tsecb: initialized
[    5.187610] nvdec nvdec: initialized
[    5.192611] falcon vic03: initialized
[    5.196014] falcon msenc: initialized
[    5.199394] falcon nvjpg: initialized
[    5.203062] tegradc tegradc.1: Display dc.54240000 registered with id=0
[    5.208308] display board info: id 0x0, fab 0x0
[    5.213177] panel_select fail by _node_status
[    5.217065] display board info: id 0x0, fab 0x0
[    5.221827] panel_select fail by _node_status
[    5.225845] parse_tmds_config: No tmds-config node
[    5.230753] of_dc_parse_platform_data: could not find vrr-settings node
[    5.237191] of_dc_parse_platform_data: could not find SD settings node
[    5.243819] of_dc_parse_platform_data: could not find cmu node
[    5.249498] of_dc_parse_platform_data: could not find cmu node for adobeRGB
[    5.256461] tegradc tegradc.1: DT parsed successfully
[    5.262656] display board info: id 0x0, fab 0x0
[    5.266289] panel_select fail by _node_status
[    5.270666] gpio wake53 for gpio=225
[    5.275415] tegradc tegradc.1: probed
[    5.282052] Console: switching to colour frame buffer device 80x30
[    5.291419] tegradc tegradc.1: fb registered
[    5.296668] tegra_camera_platform tegra-camera-platform.37: tegra_camera_probe:camera_platform_driver probe
[    5.311826] tegra-apbdma tegra-apbdma: Tegra20 APB DMA driver register 32 channels
[    5.323020] tegra-adma tegra210-adma: Tegra210 ADMA driver register 10 channels
[    5.332762] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    5.339378] No Device Node present for smmu client: serial8250 !!
[    5.345667] No Device Node present for smmu client: serial8250 !!
[    5.352925] No Device Node present for smmu client: serial8250 !!
[    5.359061] No Device Node present for smmu client: serial8250 !!
[    5.365560] of_serial 70006000.serial: RX periodic polling enabled
[    5.372056] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 68) is a Tegra
[    5.379096] console [ttyS0] enabled, bootconsole disabled
[    5.379096] console [ttyS0] enabled, bootconsole disabled
[    5.390258] tegradc tegradc.1: hdmi: spurious interrupt
[    5.397797] 70006040.serial: ttyTHS1 at MMIO 0x70006040 (irq = 69) is a SERIAL_TEGRA
[    5.410199] 70006200.serial: ttyTHS2 at MMIO 0x70006200 (irq = 78) is a SERIAL_TEGRA
[    5.422745] serial-tegra 70006300.serial: RX in PIO mode
[    5.430433] 70006300.serial: ttyTHS3 at MMIO 0x70006300 (irq = 122) is a SERIAL_TEGRA
[    5.469715] brd: module loaded
[    5.478624] loop: module loaded
[    5.484584] zram: Created 1 device(s) ...
[    5.490972] nct1008_nct72 0-004c: find device tree node, parsing dt
[    5.499521] nct1008_nct72 0-004c: starting parse dt
[    5.506712] nct1008_nct72 0-004c: success parsing dt
[    5.513947] nct1008_nct72 0-004c: success in enabling rail vdd_nct72
[    5.592069] NCT72: Enabled overheat logging at 104.00C
[    5.599359] gpio wake33 for gpio=188
[    5.605035] nct1008_nct72 0-004c: nct1008_probe: initialized
[    5.616066] THERMAL EST start of therm_fan_est_probe.
[    5.623262] THERMAL EST: found 2 subdevs
[    5.629266] THERMAL EST name: thermal-fan-est.
[    5.635846] THERMAL EST num_resources: 0
[    5.641850] [THERMAL EST subdev 0]
[    5.647251] THERMAL EST subdev name: CPU-therm
[    5.653684] THERMAL EST index 0 coeffs 50
[    5.659627] THERMAL EST index 1 coeffs 0
[    5.665400] THERMAL EST index 2 coeffs 0
[    5.671099] THERMAL EST index 3 coeffs 0
[    5.676646] THERMAL EST index 4 coeffs 0
[    5.682101] THERMAL EST index 5 coeffs 0
[    5.687456] THERMAL EST index 6 coeffs 0
[    5.692723] THERMAL EST index 7 coeffs 0
[    5.697870] THERMAL EST index 8 coeffs 0
[    5.702988] THERMAL EST index 9 coeffs 0
[    5.708069] [THERMAL EST subdev 1]
[    5.712633] THERMAL EST subdev name: GPU-therm
[    5.718217] THERMAL EST index 0 coeffs 50
[    5.723354] THERMAL EST index 1 coeffs 0
[    5.728366] THERMAL EST index 2 coeffs 0
[    5.733349] THERMAL EST index 3 coeffs 0
[    5.738233] THERMAL EST index 4 coeffs 0
[    5.743070] THERMAL EST index 5 coeffs 0
[    5.747817] THERMAL EST index 6 coeffs 0
[    5.752499] THERMAL EST index 7 coeffs 0
[    5.757126] THERMAL EST index 8 coeffs 0
[    5.761733] THERMAL EST index 9 coeffs 0
[    5.766306] THERMAL EST index 0: trip_temp 0, hyst 0
[    5.771934] THERMAL EST index 1: trip_temp 51000, hyst 15000
[    5.778234] THERMAL EST index 2: trip_temp 61000, hyst 9000
[    5.784430] THERMAL EST index 3: trip_temp 71000, hyst 9000
[    5.790627] THERMAL EST index 4: trip_temp 82000, hyst 10000
[    5.796908] THERMAL EST index 5: trip_temp 140000, hyst 0
[    5.802959] THERMAL EST index 6: trip_temp 150000, hyst 0
[    5.809001] THERMAL EST index 7: trip_temp 160000, hyst 0
[    5.815056] THERMAL EST index 8: trip_temp 170000, hyst 0
[    5.821118] THERMAL EST index 9: trip_temp 180000, hyst 0
[    5.827166] THERMAL EST index 0: trip_temps_hyst 0
[    5.832629] THERMAL EST index 1: trip_temps_hyst 36000
[    5.838442] THERMAL EST index 2: trip_temps_hyst 51000
[    5.844230] THERMAL EST index 3: trip_temps_hyst 52000
[    5.849957] THERMAL EST index 4: trip_temps_hyst 61000
[    5.855666] THERMAL EST index 5: trip_temps_hyst 62000
[    5.861378] THERMAL EST index 6: trip_temps_hyst 71000
[    5.867081] THERMAL EST index 7: trip_temps_hyst 72000
[    5.872825] THERMAL EST index 8: trip_temps_hyst 82000
[    5.878536] THERMAL EST index 9: trip_temps_hyst 140000
[    5.884353] THERMAL EST index 10: trip_temps_hyst 140000
[    5.890295] THERMAL EST index 11: trip_temps_hyst 150000
[    5.896226] THERMAL EST index 12: trip_temps_hyst 150000
[    5.902168] THERMAL EST index 13: trip_temps_hyst 160000
[    5.908101] THERMAL EST index 14: trip_temps_hyst 160000
[    5.914013] THERMAL EST index 15: trip_temps_hyst 170000
[    5.919891] THERMAL EST index 16: trip_temps_hyst 170000
[    5.925774] THERMAL EST index 17: trip_temps_hyst 180000
[    5.931660] THERMAL EST index 18: trip_temps_hyst 180000
[    5.937523] THERMAL EST index 19: trip_temps_hyst 0
[    5.942949] THERMAL EST index 20: trip_temps_hyst 0
[    5.948358] THERMAL EST init dev[0] temp hist to 25000
[    5.954082] THERMAL EST init dev[1] temp hist to 25000
[    5.959792] THERMAL EST cdev_type: pwm-fan.
[    5.964586] THERMAL EST governor name: pid_thermal_gov
[    5.970706] thermal thermal_zone7: Registering thermal zone thermal_zone7 for type thermal-fan-est.38
[    5.981477] THERMAL EST: thz register success.
[    5.986936] THERMAL EST: end of probe, return err: 0
[    5.992955] tegra_profiler: Branch: Dev
[    5.997760] tegra_profiler: Version: 1.104
[    6.002857] tegra_profiler: Samples version: 34
[    6.008413] tegra_profiler: IO version: 18
[    6.013564] armv8_pmu: imp: 0x41, idcode: 0x1
[    6.019010] armv8_pmu: arch: AA64 PmuV3 ARM CORTEX-A57, type: 5, ver: 0
[    6.026983] tegra_profiler: auth: init
[    6.032462] GPS: mt3332_gps_mod_init: platform_driver_register ret = 0
[    6.041580] t210_sata_uphy_pll_init: sata uphy already enabled
[    6.049517] tegra-sata tegra-sata.0: AHCI 0001.0301 32 slots 2 ports 3 Gbps 0x1 impl TEGRA-SATA mode
[    6.061724] tegra-sata tegra-sata.0: flags: 64bit ncq sntf pm led pmp pio slum part sadm apst 
[    6.075251] Rounding down aligned max_sectors from 4294967295 to 4294967288
[    6.084675] spi-tegra114 7000d400.spi: Static pin configuration used
[    6.093711] spi-tegra114 7000da00.spi: Static pin configuration used
[    6.103334] tun: Universal TUN/TAP device driver, 1.6
[    6.110462] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    6.119010] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[    6.127089] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[    6.136049] PPP generic driver version 2.4.2
[    6.142656] PPP BSD Compression module registered
[    6.149454] PPP Deflate Compression module registered
[    6.156618] PPP MPPE Compression module registered
[    6.163530] NET: Registered protocol family 24
[    6.170117] usbcore: registered new interface driver r8152
[    6.177839] usbcore: registered new interface driver asix
[    6.185431] usbcore: registered new interface driver ax88179_178a
[    6.193712] usbcore: registered new interface driver cdc_ether
[    6.201729] usbcore: registered new interface driver smsc95xx
[    6.209557] usbcore: registered new interface driver net1080
[    6.217242] usbcore: registered new interface driver cdc_subset
[    6.225116] usbcore: registered new interface driver zaurus
[    6.232599] usbcore: registered new interface driver cdc_ncm
[    6.240016] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    6.248785] ehci-pci: EHCI PCI platform driver
[    6.255225] tegra_xusb_read_usb_calib: usb_calib0 = 0x07a67c0f
[    6.264602] tegra-xhci tegra-xhci: XUSB device id = 0xfac (T210)
[    6.272506] usb_calib0 = 0x07a67c0f
[    6.277543] usb_calib_ext = 0x00000004
[    6.282895] usb_calib0 = 0x07a67c0f
[    6.287889] usb_calib_ext = 0x00000004
[    6.293120] usb_calib0 = 0x07a67c0f
[    6.298003] usb_calib_ext = 0x00000004
[    6.303139] xusb_prod port0 RX_CTLE = 0xfc
[    6.308575] xusb_prod port0 RX_DFE = 0xc0077f1f
[    6.314436] xusb_prod port0 RX_CDR_CTRL = 0x1c7
[    6.320272] xusb_prod port0 RX_EQ_CTRL_H = 0xfcf01368
[    6.326609] xusb_prod port1 RX_CTLE = 0xfc
[    6.331952] xusb_prod port1 RX_DFE = 0xc0077f1f
[    6.337679] xusb_prod port1 RX_CDR_CTRL = 0x1c7
[    6.343435] xusb_prod port1 RX_EQ_CTRL_H = 0xfcf01368
[    6.350835] usbcore: registered new interface driver cdc_acm
[    6.357807] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[    6.368687] usbcore: registered new interface driver cdc_wdm
[    6.375988] usbcore: registered new interface driver usb-storage
[    6.383707] usbcore: registered new interface driver usbserial
[    6.391159] usbcore: registered new interface driver ftdi_sio
[    6.398425] usbserial: USB Serial support registered for FTDI USB Serial Device
[    6.408729] usbcore: registered new interface driver option
[    6.415889] usbserial: USB Serial support registered for GSM modem (1-port)
[    6.424479] usbcore: registered new interface driver pl2303
[    6.431715] usbserial: USB Serial support registered for pl2303
[    6.439347] usbcore: registered new interface driver nvshieldled
[    6.447092] Nvidia Tegra High-Speed USB Device Controller driver (Apr 30, 2012)
[    6.458370] tegra USB phy - inst[0] platform info:
[    6.465063] port_otg: yes
[    6.469552] has_hostpc: yes
[    6.474264] phy_interface: USB_PHY_INTF_UTMI
[    6.480505] op_mode: TEGRA_USB_OPMODE_DEVICE
[    6.486696] qc2_voltage: 0
[    6.491343] vbus_pmu_irq: 0
[    6.496053] charging: enabled
[    6.500943] remote_wakeup: disabled
[    6.511417] regulator_get() failed for (tegra-udc.0,usb_bat_chg), -19
[    6.519797] tegra-udc tegra-udc.0: usb_bat_chg regulator not registered: USB charging will not be enabled
[    6.533798] mousedev: could not register psaux device, error: -16
[    6.541921] mousedev: PS/2 mouse device common for all mice
[    6.549738] usbcore: registered new interface driver xpad
[    6.557316] usbcore: registered new interface driver usb_acecad
[    6.565347] usbcore: registered new interface driver aiptek
[    6.572921] usbcore: registered new interface driver gtco
[    6.580242] usbcore: registered new interface driver hanwang
[    6.587731] usbcore: registered new interface driver kbtab
[    6.594951] otg state changed: SUSPEND --> PERIPHERAL
[    6.601800] usbcore: registered new interface driver wacom
[    6.708392] max77620-rtc max77620-rtc.1: rtc core: registered max77620-rtc as rtc0
[    6.790518] Wake51 for irq=118
[    6.795216] Enabling wake51
[    6.799658] i2c /dev entries driver
[    6.806603] i2c i2c-6: of_i2c: modalias failure on /i2c@546c0000/tca6408@21
[    6.815808] virtual_init
[    6.820867] [IMX135] sensor driver loading
[    6.826804] [imx132] sensor driver loading
[    6.832697] [ar0261] sensor driver loading
[    6.838665] ov7695 sensor driver loading
[    6.844402] mt9m114 sensor driver loading
[    6.850380] pcl-generic pcl-generic: virtual_chip_add
[    6.858422] usbcore: registered new interface driver uvcvideo
[    6.865852] USB Video Class driver (1.1.1)
[    6.872297] max77620-power-off max77620-power-off.4: Event recorder REG_NVERC : 0x0
[    6.883901] FAN dev name: pwm-fan
[    6.888903] FAN:gpio request success.
[    6.894327] pwm_fan_driver pwm-fan.35: cap state:7, cap pwm:255
[    6.902273] pwm_fan_driver pwm-fan.35: got pwm for fan
[    6.909449] pwm_fan_driver pwm-fan.35: index 0: pwm=0, rpm=0, rru=40, rrd=40, state:2
[    6.921043] pwm_fan_driver pwm-fan.35: index 1: pwm=80, rpm=1000, rru=2, rrd=2, state:2
[    6.932931] pwm_fan_driver pwm-fan.35: index 2: pwm=120, rpm=2000, rru=1, rrd=1, state:2
[    6.944965] pwm_fan_driver pwm-fan.35: index 3: pwm=160, rpm=3000, rru=1, rrd=1, state:2
[    6.957333] pwm_fan_driver pwm-fan.35: index 4: pwm=255, rpm=4000, rru=1, rrd=1, state:3
[    6.969835] pwm_fan_driver pwm-fan.35: index 5: pwm=255, rpm=5000, rru=1, rrd=1, state:3
[    6.982588] pwm_fan_driver pwm-fan.35: index 6: pwm=255, rpm=6000, rru=1, rrd=1, state:3
[    6.995698] pwm_fan_driver pwm-fan.35: index 7: pwm=255, rpm=7000, rru=1, rrd=1, state:4
[    7.009056] pwm_fan_driver pwm-fan.35: index 8: pwm=255, rpm=10000, rru=1, rrd=1, state:4
[    7.022680] pwm_fan_driver pwm-fan.35: index 9: pwm=255, rpm=11000, rru=1, rrd=1, state:4
[    7.038060] tegra_aotag tegra-aotag.21: AOTAG probe started
[    7.046574] tegra_aotag tegra-aotag.21: nominal ft -- 105
[    7.054825] tegra_aotag tegra-aotag.21: tall -- 76
[    7.062396] tegra_aotag tegra-aotag.21: tiddq -- 1
[    7.069928] tegra_aotag tegra-aotag.21: ten-count -- 16
[    7.077892] tegra_aotag tegra-aotag.21: tsample -- 9
[    7.085492] tegra_aotag tegra-aotag.21: pdiv -- 8
[    7.092725] tegra_aotag tegra-aotag.21: nominal cp -- 25
[    7.100484] tegra_aotag tegra-aotag.21: pdiv-ate -- 8
[    7.107881] tegra_aotag tegra-aotag.21: tsamp-ate -- 39
[    7.115375] tegra_aotag tegra-aotag.21: compensation A,B -- 10632,-67490
[    7.124308] tegra_aotag tegra-aotag.21: sensor found :ID 0, Name: aotag0
[    7.133182] tegra_aotag tegra-aotag.21: reading fuse value for sensor 0
[    7.141880] tegra_aotag tegra-aotag.21: base-cp:22a shifted-cp:1
[    7.149876] tegra_aotag tegra-aotag.21: base-ft:4b8 shifted-ft:fffffff5
[    7.158416] tegra_aotag tegra-aotag.21: actual_aotag_cp 255, ft 995
[    7.166544] tegra_aotag tegra-aotag.21: - Tsens calib value - 0x3ae5d27
[    7.174959] tegra_aotag tegra-aotag.21: CPmask 1fff FTmask 3ffe000
[    7.182871] tegra_aotag tegra-aotag.21: Tsense calib CP - 0x1d27
[    7.190533] tegra_aotag tegra-aotag.21: Tsense Actual CP d.34727
[    7.198093] tegra_aotag tegra-aotag.21: Tsense calib FT - 0x1d72
[    7.205577] tegra_aotag tegra-aotag.21: Tsense Actual FT d.38002
[    7.212979] tegra_aotag tegra-aotag.21: delta ts 3275, temp 740
[    7.220203] tegra_aotag tegra-aotag.21: thermA-852, thermB--813
[    7.227366] tegra_aotag tegra-aotag.21: Registering sensor 0
[    7.234252] tegra_aotag tegra-aotag.21: Bound to TZ : ID 0
[    7.240929] tegra_aotag tegra-aotag.21: shutdown temperature - 55
[    7.248217] tegra_aotag tegra-aotag.21: AOTAG EN 60
[    7.254303] tegra_aotag tegra-aotag.21: Probe done [SUCCESS]:0
[    7.261940] md: raid0 personality registered for level 0
[    7.268825] device-mapper: uevent: version 1.0.3
[    7.275136] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[    7.286848] Tegra210 cpuidle driver
[    7.293242] sdhci: Secure Digital Host Controller Interface driver
[    7.300987] sdhci: Copyright(c) Pierre Ossman
[    7.306881] sdhci-pltfm: SDHCI platform and OF driver helper
[    7.314553] mmc0: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[    7.328440] sdhci-tegra sdhci-tegra.3: Parent select= pll_p rate=408000000
[    7.337151] sdhci-tegra sdhci-tegra.3: Parent select= pll_c4_out2 rate=199680000
[    7.348935] sdhci-tegra sdhci-tegra.3: Speedo value 1992
[    7.356134] sdhci-tegra sdhci-tegra.3: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[    7.368946] regulator_get() failed for (sdhci-tegra.3,vqmmc), -19
[    7.377117] mmc0: no vqmmc regulator found
[    7.383306] regulator_get() failed for (sdhci-tegra.3,vmmc), -19
[    7.391468] mmc0: no vmmc regulator found
[    7.430258] mmc0: SDHCI controller on sdhci-tegra.3 [sdhci-tegra.3] using ADMA
[    7.442488] mmc1: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[    7.457902] sdhci-tegra sdhci-tegra.1: Parent select= pll_p rate=408000000
[    7.468284] sdhci-tegra sdhci-tegra.1: Speedo value 1992
[    7.476172] sdhci-tegra sdhci-tegra.1: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[    7.490739] regulator_get() failed for (sdhci-tegra.1,vqmmc), -19
[    7.499379] mmc1: no vqmmc regulator found
[    7.505985] regulator_get() failed for (sdhci-tegra.1,vmmc), -19
[    7.514540] mmc1: no vmmc regulator found
[    7.560262] mmc1: SDHCI controller on sdhci-tegra.1 [sdhci-tegra.1] using ADMA
[    7.573722] mmc2: sdhci_tegra_probe line=5655 runtime pm type=mmc rtpm coupled with clock gate, disable-clock-gate=0
[    7.589371] sdhci-tegra sdhci-tegra.0: Parent select= pll_p rate=408000000
[    7.599857] sdhci-tegra sdhci-tegra.0: Speedo value 1992
[    7.607818] sdhci-tegra sdhci-tegra.0: Tuning constraints: nom_mv 1075, boot_mv 1075, min_or_mv 0
[    7.621976] regulator_get() failed for (sdhci-tegra.0,vqmmc), -19
[    7.630700] mmc2: no vqmmc regulator found
[    7.637368] regulator_get() failed for (sdhci-tegra.0,vmmc), -19
[    7.646014] mmc0: BKOPS_EN bit is not set
[    7.646024] mmc2: no vmmc regulator found
[    7.680265] mmc2: SDHCI controller on sdhci-tegra.0 [sdhci-tegra.0] using ADMA
[    7.692582] gpio wake35 for gpio=201
[    7.702693] tegra-se tegra21-se: tegra_se_probe: complete
[    7.711148] hidraw: raw HID events driver (C) Jiri Kosina
[    7.721431] usbcore: registered new interface driver usbhid
[    7.729425] usbhid: USB HID core driver
[    7.735659] tegra_bootloader_debug: Created tegra_bootloader directory
[    7.744602] tegra_bootloader_debug: Created sysfs interface tegra_bootloader_verify_regs in tegra_bootloader directory
[    7.760008] tegra_bootloader_debug: Created sysfs interface tegra_bootloader_prof in tegra_bootloader directory
[    7.775272] nvadsp 702ef000.adsp: in probe()...
[    7.783024] nvadsp 702ef000.adsp: AMC/ARAM initialized.
[    7.790730] nvadsp 702ef000.adsp: nvadsp_app_module_probe
[    7.797438] mmc0: tap value and tuning window after hw tuning completion ...
[    7.797445] mmc0: tuning_window[0]: 0x9fffffff
[    7.797451] mmc0: tuning_window[1]: 0x7fffffff
[    7.797456] mmc0: tuning_window[2]: 0xfffffffe
[    7.797460] mmc0: tuning_window[3]: 0x7ffffff9
[    7.797465] mmc0: tuning_window[4]: 0x0
[    7.797470] mmc0: tuning_window[5]: 0x0
[    7.797474] mmc0: tuning_window[6]: 0x0
[    7.797478] mmc0: tuning_window[7]: 0x0
[    7.797482] sdhci: Tap value: 46 | Trim value: 8
[    7.797486] sdhci: SDMMC Interrupt status: 0x00040000
[    7.798063] mmc0: switch to HS400 mode is successful
[    7.802066] mmc0: new HS400 MMC card at address 0001
[    7.802530] mmcblk0: mmc0:0001 016G32 14.6 GiB 
[    7.802746] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB
[    7.803969]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18
[    7.833294] mmc1: queuing unknown CIS tuple 0x80 (5 bytes)
[    7.916264] tegra_throttle : init passed
[    7.923512] cpu-tegra: init EDP limit: 1224 MHz
[    7.930117] pll_x: not ready for dynamic ramp to 614400000
[    7.937221] pll_x: not ready for dynamic ramp to 614400000
[    7.949432] soctherm: skipping sensor 4 programming
[    7.956037] soctherm: skipping sensor 5 programming
[    7.996614] usbcore: registered new interface driver snd-usb-audio
[    8.004610] No Device Node present for smmu client: snd-soc-dummy !!
[    8.012636] No Device Node present for smmu client: snd-soc-dummy !!
[    8.021047] No Device Node present for smmu client: snd-soc-dummy !!
[    8.029107] No Device Node present for smmu client: snd-soc-dummy !!
[    8.029431] mmc1: tap value and tuning window after hw tuning completion ...
[    8.029439] mmc1: tuning_window[0]: 0xe3ffffff
[    8.029444] mmc1: tuning_window[1]: 0x7fffffff
[    8.029450] mmc1: tuning_window[2]: 0xfffffffc
[    8.029454] mmc1: tuning_window[3]: 0x7fffffcf
[    8.029459] mmc1: tuning_window[4]: 0x0
[    8.029464] mmc1: tuning_window[5]: 0x0
[    8.029468] mmc1: tuning_window[6]: 0x0
[    8.029473] mmc1: tuning_window[7]: 0x0
[    8.029477] sdhci: Tap value: 45 | Trim value: 8
[    8.029481] sdhci: SDMMC Interrupt status: 0x00040000
[    8.034567] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[    8.034613] mmc1: new ultra high speed SDR104 SDIO card at address 0001
[    8.121034] Codec driver version 0.4 alsa 1.0.25
[    8.131851] tegra-i2c 7000c000.i2c: no acknowledge from address 0x1b
[    8.139800] rt5659 0-001b: Device with ID register ffffffc0 is not rt5659
[    8.165222] tegra210-i2s tegra210-i2s.0: Missing prop fsync-width for I2S0
[    8.174947] tegra210-i2s tegra210-i2s.2: Missing prop fsync-width for I2S2
[    8.183743] tegra210-i2s tegra210-i2s.3: Missing prop fsync-width for I2S3
[    8.192672] tegra210-i2s tegra210-i2s.4: Missing prop fsync-width for I2S4
[    8.210065] OPE platform probe
[    8.214906] OPE platform probe successful
[    8.220455] OPE platform probe
[    8.225313] OPE platform probe successful
[    8.231151] tegra210_adsp_audio_platform_probe: platform probe started
[    8.240889] tegra210-adsp adsp_audio.3: Default param-type to BYTE for mp3-dec1
[    8.251622] tegra210-adsp adsp_audio.3: Default param-type to BYTE for spkprot
[    8.262842] tegra210-adsp adsp_audio.3: Default param-type to BYTE for src
[    8.272128] tegra210-adsp adsp_audio.3: Default param-type to BYTE for aac-dec1
[    8.284046] tegra210_adsp_audio_platform_probe probe successfull.
[    8.296828] tegra-snd-t210ref-mobile-rt565x sound.18: ASoC: CODEC (null) not registered
[    8.311713] tegra-snd-t210ref-mobile-rt565x sound.18: snd_soc_register_card failed (-517)
[    8.324695] platform sound.18: Driver tegra-snd-t210ref-mobile-rt565x requests probe deferral
[    8.339198] GACT probability NOT on
[    8.345117] Mirror/redirect action on
[    8.351140] u32 classifier
[    8.356195]     Actions configured
[    8.362018] Netfilter messages via NETLINK v0.30.
[    8.369286] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[    8.378400] ctnetlink v0.93: registering with nfnetlink.
[    8.386423] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[    8.396081] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[    8.405092] xt_time: kernel timezone is -0000
[    8.412305] ipip: IPv4 over IPv4 tunneling driver
[    8.420313] ip_tables: (C) 2000-2006 Netfilter Core Team
[    8.428499] arp_tables: (C) 2002 David S. Miller
[    8.435756] TCP: cubic registered
[    8.441568] Initializing XFRM netlink socket
[    8.448886] NET: Registered protocol family 10
[    8.456970] mip6: Mobile IPv6
[    8.462418] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    8.470522] sit: IPv6 over IPv4 tunneling driver
[    8.478755] NET: Registered protocol family 17
[    8.485595] NET: Registered protocol family 15
[    8.492249] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    8.500379] Bluetooth: HIDP socket layer initialized
[    8.507458] NET: Registered protocol family 35
[    8.514026] Key type dns_resolver registered
[    8.520342] NET: Registered protocol family 41
[    8.529505] Registering SWP/SWPB emulation handler
[    8.588830] isp isp.0: initialized
[    8.596049] isp isp.1: initialized
[    8.602046] vdd_gpu: disabling
[    8.607240] en-vdd-cam-1v2: disabling
[    8.613020] en-vdd-cam-hv-2v8: disabling
[    8.618957] en-vdd-disp-1v8: disabling
[    8.624686] en-mdm-pwr-3v7: disabling
[    8.630270] en-vdd-disp-3v3: disabling
[    8.635901] en-vdd-ts-hv-3v3: disabling
[    8.641600] en-vdd-ts-1v8: disabling
[    8.646973] usb-vbus3: disabling
[    8.651823] usb-vbus1: disabling
[    8.656610] vdd-fan: disabling
[    8.667562] vdd-disp-3v0: disabling
[    8.672594] snsr_pm: disabling
[    8.677089] aux-3v3: disabling
[    8.681531] en-vdd-cam: disabling
[    8.686374] en-vdd-sd: disabling
[    8.695881] lcd-bl-en: disabling
[    8.700429] max77620-gpio7: disabling
[    8.717037] vdd-cpu-fixed: disabling
[    8.721909] regulator-dummy: disabling
[    8.728378] tegra-snd-t210ref-mobile-rt565x: probe of sound.18 failed with error -16
[    8.740182] gpio wake24 for gpio=189
[    8.745275] gpio wake27 for gpio=192
[    8.750325] gpio wake25 for gpio=190
[    8.755493] input: gpio-keys as /devices/platform/gpio-keys.39/input/input0
[    8.780787] max77620-rtc max77620-rtc.1: setting system clock to 2016-04-29 00:59:34 UTC (1461891574)
[    8.793790] [dram-timers] DRAM derating cdev registered.
[    8.800822] Disable partitions left on by BL
[    8.806766]     sata
[    8.810745]     disb
[    8.814586] Disabling clocks left on by bootloader:
[    8.821157]    audio2_dmic
[    8.825599]    audio1_dmic
[    8.829989]    audio0_dmic
[    8.834357]    audio_2x
[    8.838420]    audio
[    8.842222]    audio4
[    8.846062]    audio3
[    8.849873]    audio2
[    8.853684]    audio1
[    8.857439]    audio0
[    8.861249]    entropy
[    8.865024]    dsi2-fixed
[    8.868959]    dsi1-fixed
[    8.872863]    sdmmc4_ddr
[    8.876649]    sdmmc1_ddr
[    8.880492]    sor1_src
[    8.884117]    cclk_lp
[    8.888557] tegra_cl_dvfs 70110000.dfll-ovr: DT data retrieved successfully
[    8.896915] tune_cpu_trimmers: init soctherm cpu zone LOW
[    8.903587] tegra_cl_dvfs_init_cdev: cpu_cold cooling device registered
[    8.911474] tegra_cl_dvfs_init_cdev: cpu_hot cooling device registered
[    8.911865] Tegra CPU DFLL is initialized with use_dfll = 1
[    8.912079] tegra_dvfs: 0.vdd-cpu-rail-ovr connected to regulator 
[    8.933275] tegra_dvfs: 4.vdd-core-rail-max77620 connected to regulator 
[    8.941453] tegra_dvfs: 1.vdd-gpu-rail-ovr connected to regulator 
[    8.949393] CPU rate: 614 MHz
[    8.953554] last reset is due to power on reset
[    8.953554] 
[    8.961227] KERNEL: PMC reset status reg: 0x0
[    8.967125] tegra_actmon.emc: Completed initialization (0)
[    8.974087] tegra_actmon.avp: Completed initialization (0)
[    9.226940] tegra dvfs: tegra sysfs cap interface is initialized
[    9.234224] tegra dvfs: tegra sysfs gpu interface is initialized
[    9.242808] ALSA device list:
[    9.246514]   #0: HDA NVIDIA Tegra at 0x70038000 irq 113
[    9.252833] md: Waiting for all devices to be available before autodetect
[    9.260572] md: If you don't use raid, use raid=noautodetect
[    9.267443] md: Autodetecting RAID arrays.
[    9.272448] md: Scanned 0 and added 0 devices.
[    9.277790] md: autorun ...
[    9.281502] md: ... autorun DONE.
[    9.286875] EXT4-fs (mmcblk0p1): couldn't mount as ext3 due to feature incompatibilities
[    9.297808] EXT4-fs (mmcblk0p1): couldn't mount as ext2 due to feature incompatibilities
[    9.352856] EXT4-fs (mmcblk0p1): 5 orphan inodes deleted
[    9.359154] EXT4-fs (mmcblk0p1): recovery complete
[    9.371988] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[    9.382021] VFS: Mounted root (ext4 filesystem) on device 179:1.
[    9.391166] devtmpfs: mounted
[    9.395239] Freeing unused kernel memory: 428K (ffffffc001065000 - ffffffc0010d0000)
[    9.405042] Freeing alternatives memory: 52K (ffffffc0010d1000 - ffffffc0010de000)
Mount failed for selinuxfs on /sys/fs/selinux:  No such file or directory
[    9.551879] init: plymouth-upstart-bridge main process (128) terminated with status 1
[    9.562288] init: plymouth-upstart-bridge main process ended, respawning
[    9.586087] init: plymouth-upstart-bridge main process (138) terminated with status 1
[    9.596510] init: plymouth-upstart-bridge main process ended, respawning
[    9.605139] init: ureadahead main process (131) terminated with status 5
[    9.627237] init: plymouth-upstart-bridge main process (141) terminated with status 1
[    9.637663] init: plymouth-upstart-bridge main process ended, respawning
 * Starting Mount filesystems on boot                                    [ OK ]
 * Starting Signal sysvinit that the rootfs is mounted                   [ OK ]
 * Starting Clean /tmp directory                                         [ OK ]
 * Starting Populate and link to /run filesystem                         [ OK ]
 * Stopping Populate and link to /run filesystem                         [ OK ]
 * Stopping Track if upstart is running in a container                   [ OK ]
 * Stopping Clean /tmp directory                                         [ OK ]
 * Starting Initialize or finalize resolvconf                            [ OK ]
 * Starting set console keymap                                           [ OK ]
 * Starting Signal sysvinit that virtual filesystems are mounted         [ OK ]
 * Starting Signal sysvinit that virtual filesystems are mounted         [ OK ]
 * Starting Bridge udev events into upstart                              [ OK ]
 * Stopping set console keymap                                           [ OK ]
 * Starting Signal sysvinit that local filesystems are mounted           [ OK ]
 * Starting Signal sysvinit that remote filesystems are mounted          [ OK ]
 * Starting device node and kernel event manager                         [ OK ]
 * Starting NFSv4 id <-> name mapper                                     [ OK ]
 * Starting flush early job output to logs                               [ OK ]
 * Starting D-Bus system message bus                                     [ OK ]
 * Stopping Mount filesystems on boot                                    [ OK ]
 * Starting NVIDIA specific init script                                  [ OK ]
 * Starting load modules from /etc/modules                               [ OK ]
 * Starting cold plug devices                                            [ OK ]
 * Starting log initial device creation                                  [ OK ]
 * Stopping flush early job output to logs                               [ OK ]
 * Stopping load modules from /etc/modules                               [ OK ]
 * Starting SystemD login management service                             [ OK ]
 * Stopping NVIDIA specific init script                                  [ OK ]
 * Starting bluetooth daemon                                             [ OK ]
 * Stopping rpcsec_gss daemon                                            [ OK ]
 * Stopping NVIDIA specific first-boot script                            [ OK ]
 * Starting system logging daemon                                        [ OK ]
 * Starting mDNS/DNS-SD daemon                                           [ OK ]
 * Starting Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
 * Stopping NVIDIA bluetooth/wifi init script                            [ OK ]
 * Stopping Reload cups, upon starting avahi-daemon to make sure remote q[ OK ]are populated
 * Starting set console font                                             [ OK ]
 * Stopping set console font                                             [ OK ]
 * Starting userspace bootsplash                                         [ OK ]
 * Stopping userspace bootsplash                                         [ OK ]
 * Starting Send an event to indicate plymouth is up                     [ OK ]
 * Stopping Send an event to indicate plymouth is up                     [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device                                     [ OK ]
 * Starting configure network device                                     [ OK ]
 * Starting configure network device                                     [ OK ]
 * Starting configure network device                                     [ OK ]
 * Starting configure network device                                     [ OK ]
 * Starting Mount network filesystems                                    [ OK ]
 * Starting Upstart job to start rpcbind on boot only                    [ OK ]
 * Starting Failsafe Boot Delay                                          [ OK ]
 * Stopping Upstart job to start rpcbind on boot only                    [ OK ]
 * Stopping cold plug devices                                            [ OK ]
 * Stopping log initial device creation                                  [ OK ]
 * Stopping NVIDIA bluetooth/wifi init script                            [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting enable remaining boot-time encrypted block devices           [ OK ]
 * Starting configure network device                                     [ OK ]
 * Stopping Failsafe Boot Delay                                          [ OK ]
 * Starting RPC portmapper replacement                                   [ OK ]
 * Starting System V initialisation compatibility                        [ OK ]
 * Starting nvcamera daemon                                              [ OK ]
 * Starting modem connection manager                                     [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure virtual network devices                            [ OK ]
 * Starting early crypto disks...                                        [ OK ] 
 * Stopping Mount network filesystems                                    [ OK ]
 * Starting NSM status monitor                                           [ OK ]
 * Setting up X socket directories...                                    [ OK ] 
 * Starting network connection manager                                   [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device                                     [ OK ]
 * Stopping System V initialisation compatibility                        [ OK ]
 * Starting configure network device security                            [ OK ]
 * Starting configure network device                                     [ OK ]
 * speech-dispatcher disabled; edit /etc/default/speech-dispatcher
 * Starting System V runlevel compatibility                              [ OK ]
 * Starting Restore Sound Card State                                     [ OK ]
 * Starting regular background program processing daemon                 [ OK ]
 * Starting anac(h)ronistic cron                                         [ OK ]
 * Starting save kernel messages                                         [ OK ]
 * Starting Restore Sound Card State                                     [fail]
 * Stopping save kernel messages                                         [ OK ]
 * Starting NTP server ntpd        * Stopping anac(h)ronistic cron       [ OK ]
                                                                         [ OK ] 
saned disabled; edit /etc/default/saned
 * Stopping System V runlevel compatibility                              [ OK ]

Ubuntu 14.04.1 LTS tegra-ubuntu ttyS0

tegra-ubuntu login: ubuntu (automatic login)

Last login: Fri Apr 29 00:33:33 UTC 2016 on ttyS0
Welcome to Ubuntu 14.04.1 LTS (GNU/Linux 3.10.67-gbaaa7aa-dirty aarch64)

 * Documentation:  https://help.ubuntu.com/

505 packages can be updated.
247 updates are security updates.

ubuntu@tegra-ubuntu:~$