Boundary Devices iMX6 Demo 20140303
Introduction
Boundary Devices demo after Eric Nelson Correction in prep-touscreen script in order to support the new displays.
Boot log (HDMI monitor + USB mouse + 1024x600 ft5x06 display + 800x400 tsc2004 display)
U-Boot 2013.10 (Feb 28 2014 - 14:31:53) CPU: Freescale i.MX6Q rev1.2 at 792 MHz CPU: Temperature 27 C, calibration data: 0x56c4ba7d Reset cause: POR Board: SABRE Lite DRAM: 1 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 SF: Detected SST25VF016B with page size 256 Bytes, erase size 4 KiB, total 2 MiB auto-detected panel HDMI Display: HDMI (1024x768) In: serial Out: serial Err: serial Net: using phy at 6 FEC [PRIME] Hit any key to stop autoboot: 0 AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl SATA mode flags: ncq stag pm led clo only pmp pio slum part No port device detected! ** Bad device size - sata 0 ** ** Bad device size - sata 0 ** SATA device 1: unknown device ** Bad device sata 1 ** ** Bad device sata 1 ** MMC: no card present mmc0(part 0) is current device MMC: no card present ** Bad device mmc 0 ** MMC: no card present ** Bad device mmc 0 ** MMC: no card present mmc1(part 0) is current device MMC: no card present ** Bad device mmc 1 ** MMC: no card present ** Bad device mmc 1 ** (Re)start USB... USB0: USB EHCI 1.00 scanning bus 0 for devices... 4 USB Device(s) found scanning usb for storage devices... 1 Storage Device(s) found scanning usb for ethernet devices... 0 Ethernet Device(s) found USB device 0: Device 0: Vendor: SanDisk Rev: 1.20 Prod: Cruzer Type: Removable Hard Disk Capacity: 15267.0 MB = 14.9 GB (31266816 x 512) ... is now current device reading /6x_bootscript 3304 bytes read in 29 ms (110.4 KiB/s) ## Executing script at 10008000 reading uEnv.txt 50 bytes read in 17 ms (2 KiB/s) Setting bus to 1 Valid chip addresses: 50 Setting bus to 2 Valid chip addresses: ------ no Freescale display Valid chip addresses: 38 Valid chip addresses: 48 reading imx6q-sabrelite.dtb ** Unable to read file imx6q-sabrelite.dtb ** only CEA modes allowed on HDMI port reading uImage 4071048 bytes read in 289 ms (13.4 MiB/s) ## Booting kernel from Legacy Image at 10800000 ... Image Name: "RR Compressed Linux Kernel" Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 4070984 Bytes = 3.9 MiB Load Address: 10008000 Entry Point: 10008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Linux version 3.0.35-ridgerun (efernandez@RidgeRun-PC) (gcc version 4.8.2 20130603 (prerelease) (crosstool-NG 1.19.0 - Linaro GCC 2013.07) ) #2 SMP PREEMPT Mon Mar 3 09:03:01 CST 2014 CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: Boundary Devices Nitrogen6X/SABRE Lite Board Memory policy: ECC disabled, Data cache writealloc CPU identified as i.MX6Q, silicon rev 1.2 PERCPU: Embedded 7 pages/cpu @8bec8000 s5440 r8192 d15040 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 186688 Kernel command line: video=mxcfb0:dev=hdmi,1280x720M@60,if=RGB24 video=mxcfb1:dev=ldb,1024x600M@60,if=RGB666 ft5x06_ts.screenres=1024,600 video=mxcfb2:dev=lcd,CLAA-WVGA,if=RGB666 video=mxcfb3:off fbmem=28M,10M,10M mem=864M console=ttymxc1,115200 vmalloc=400M consoleblank=0 root=/dev/sda2 rootwait rootfstype=ext3 mxc_hdmi.only_cea=1 PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 640MB 96MB = 736MB total Memory: 737516k/737516k available, 147220k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xf4600000 - 0xffe00000 ( 184 MB) vmalloc : 0xb6800000 - 0xf2000000 ( 952 MB) lowmem : 0x80000000 - 0xb6000000 ( 864 MB) pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) modules : 0x7f000000 - 0x7fe00000 ( 14 MB) .init : 0x80008000 - 0x80047000 ( 252 kB) .text : 0x80047000 - 0x8076bc50 (7316 kB) .data : 0x8076c000 - 0x807c93c0 ( 373 kB) .bss : 0x807c93e4 - 0x80817b4c ( 314 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Preemptible hierarchical RCU implementation. NR_IRQS:624 MXC GPIO hardware sched_clock: 32 bits at 3000kHz, resolution 333ns, wraps every 1431655ms arm_max_freq=1GHz MXC_Early serial console at MMIO 0x21e8000 (options '115200') bootconsole [ttymxc1] enabled Console: colour dummy device 80x30 Calibrating delay loop... 1581.05 BogoMIPS (lpj=7905280) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available CPU1: Booted secondary processor CPU2: Booted secondary processor CPU3: Booted secondary processor Brought up 4 CPUs SMP: Total of 4 processors activated (6324.22 BogoMIPS). devtmpfs: initialized print_constraints: dummy: NET: Registered protocol family 16 print_constraints: vddpu: 725 <--> 1300 mV at 1100 mV fast normal print_constraints: vddcore: 725 <--> 1300 mV at 1100 mV fast normal print_constraints: vddsoc: 725 <--> 1300 mV at 1200 mV fast normal print_constraints: vdd2p5: 2000 <--> 2775 mV at 2400 mV fast normal print_constraints: vdd1p1: 800 <--> 1400 mV at 1100 mV fast normal print_constraints: vdd3p0: 2625 <--> 3400 mV at 3000 mV fast normal lcd_disable_pins ------------ Board type Sabre Lite imx_add_mxc_pwm:pdata= (null) imx_add_mxc_pwm:pdata= (null) imx_add_mxc_pwm:pdata=8078fd78 imx_add_mxc_pwm:pdata= (null) Flexcan NXP tja1040 hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step. hw-breakpoint: maximum watchpoint size is 4 bytes. L310 cache controller enabled l2x0: 16 ways, CACHE_ID 0x410000c7, AUX_CTRL 0x02070000, Cache size: 1048576 B bio: create slab <bio-0> at 0 print_constraints: VDDA: 2500 mV print_constraints: VDDIO: 3300 mV machine_constraints_voltage: VDDD: unsupportable voltage constraints reg-fixed-voltage reg-fixed-voltage.2: Failed to register regulator: -22 reg-fixed-voltage: probe of reg-fixed-voltage.2 failed with error -22 print_constraints: vmmc: 3300 mV vgaarb: loaded SCSI subsystem initialized spi_imx imx6q-ecspi.0: probed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Freescale USB OTG Driver loaded, $Revision: 1.55 $ imx-ipuv3 imx-ipuv3.0: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) imx-ipuv3 imx-ipuv3.1: IPU DMFC NORMAL mode: 1(0~1), 5B(4,5), 5F(6,7) mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 driver probed mxc_mipi_csi2 mxc_mipi_csi2: i.MX MIPI CSI2 dphy version is 0x3130302a MIPI CSI2 driver module loaded Advanced Linux Sound Architecture Driver Version 1.0.24. Bluetooth: Core ver 2.16 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized cfg80211: Calling CRDA to update world regulatory domain i2c-core: driver [max17135] using legacy suspend method i2c-core: driver [max17135] using legacy resume method Switching to clocksource mxc_timer1 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. PMU: registered new PMU device of type 0 Static Power Management for Freescale i.MX6 wait mode is enabled for i.MX6 cpaddr = b6880000 suspend_iram_base=b6918000 PM driver module loaded iMX6 PCIe PCIe RC mode imx_pcie_pltfm_probe entering. PCIE: imx_pcie_pltfm_probe start link up. link up failed, DB_R0:0x00ae6d00, DB_R1:0x08200000! IMX PCIe port: link down! IMX usb wakeup probe add wake up source irq 75 IMX usb wakeup probe cpu regulator mode:ldo_enable i.MXC CPU frequency driver squashfs: version 4.0 (2009/01/31) Phillip Lougher JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 1440 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 MIPI DSI driver module loaded mxc_sdc_fb mxc_sdc_fb.0: register mxc display driver hdmi mxc_hdmi mxc_hdmi: Detected HDMI controller 0x13:0xa:0xa0:0xc1 fbcvt: 1280x720@60: CVT Name - .921M9 ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 imx-ipuv3 imx-ipuv3.1: IPU DMFC DP HIGH RESOLUTION: 1(0,1), 5B(2~5), 5F(6,7) pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 Console: switching to colour frame buffer device 160x45 mxc_sdc_fb mxc_sdc_fb.1: register mxc display driver ldb _regulator_get: get() with no identifier fbcvt: Aspect ratio not CVT standard fbcvt: 1024x600@60: CVT Name - Not a CVT standard - 0.614 Mega Pixel Image ldb_disp_init: ret=1, 1024x600 ldb_disp_init:r=59, x=1024, y=600, p=20408, l=144, r=40, upper=3, lower=11, h=104, v=10 ldb_disp_init: 1280x800 ipu_init_sync_panel: disp=0, pixel_clk=49000000 48489795 pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 mxc_sdc_fb mxc_sdc_fb.2: register mxc display driver lcd lcd_enable_pins ipu_init_sync_panel: disp=0, pixel_clk=27000000 27000000 mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 0(VIC 4): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 1(VIC 2): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 3(VIC 1): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 19(VIC 2): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 20(VIC 3): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 21(VIC 17): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 22(VIC 18): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 23(VIC 19): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 24(VIC 4): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 27(VIC 31): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 28(VIC 16): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 29(VIC 18): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 32(VIC 19): mxc_hdmi mxc_hdmi: mxc_hdmi_edid_rebuild_modelist: Added mode 33(VIC 31): pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 fbcvt: 1280x720@60: CVT Name - .921M9 ipu_init_sync_panel: disp=1, pixel_clk=25175000 25142857 mxc_sdc_fb mxc_sdc_fb.3: mxcfb3 is turned off! imx-sdma imx-sdma: loaded firmware 1.1 ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 imx-sdma imx-sdma: initialized Serial: IMX driver imx-uart.0: ttymxc0 at MMIO 0x2020000 (irq = 58) is a IMX imx-uart.1: ttymxc1 at MMIO 0x21e8000 (irq = 59) is a IMX old_ufcr=a81 new_ufcr=b01, old_ucr2=4027 new_ucr2=4027, old_ubir=f num=1f7, old_ubmr=15b denom=c34 clk=80000000 div=7 num=504 denom=3125 baud=115200 console [ttymxc1] enabled, bootconsole disabled console [ttymxc1] enabled, bootconsole disabled loop: module loaded Can't recover from RESET HBA! No sata disk. m25p80 spi0.0: sst25vf016b (2048 Kbytes) Creating 3 MTD partitions on "m25p80": 0x000000000000-0x0000000c0000 : "bootloader" 0x0000000c0000-0x0000000c2000 : "ubparams" 0x0000000c2000-0x000000200000 : "unused" vcan: Virtual CAN interface driver CAN device driver interface flexcan netdevice driver flexcan imx6q-flexcan.0: device registered (reg_base=b69e8000, irq=142) FEC Ethernet Driver fec_enet_mii_bus: probed tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 75, io base 0x02184000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected add wake up source irq 72 fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2 fsl-ehci fsl-ehci.1: irq 72, io base 0x02184200 fsl-ehci fsl-ehci.1: USB 2.0 started, EHCI 1.00 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial usbserial: USB Serial Driver core USB Serial support registered for FTDI USB Serial Device usbcore: registered new interface driver ftdi_sio ftdi_sio: v1.6.0:USB FTDI Serial Converters Driver USB Serial support registered for Keyspan - (without firmware) USB Serial support registered for Keyspan 1 port adapter USB Serial support registered for Keyspan 2 port adapter USB Serial support registered for Keyspan 4 port adapter usbcore: registered new interface driver keyspan keyspan: v1.1.5:Keyspan USB to Serial Converter Driver USB Serial support registered for GSM modem (1-port) usbcore: registered new interface driver option option: v0.7.2:USB Driver for GSM modems USB Serial support registered for Qualcomm USB modem usbcore: registered new interface driver qcserial ARC USBOTG Device Controller driver (1 August 2005) mousedev: PS/2 mouse device common for all mice input: gpio-keys as /devices/platform/gpio-keys/input/input0 input: tsc2004 as /devices/virtual/input/input1 egalax_ts 2-0004: egalax_ts: failed to read firmware version egalax_ts: probe of 2-0004 failed with error -5 ts_probe: ft5x06 touchscreen irq=265, gp=9 input: ft5x06 as /devices/virtual/input/input2 ft5x06: Mar 3 2014 i2c-core: driver [isl29023] using legacy suspend method i2c-core: driver [isl29023] using legacy resume method check_alarm_past: alarm in the past snvs_rtc snvs_rtc.0: rtc core: registered snvs_rtc as rtc0 i2c /dev entries driver Linux video capture interface: v2.00 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video16 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video17 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video18 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video19 mxc_v4l2_output mxc_v4l2_output.0: V4L2 device registered as video20 i2c-core: driver [mag3110] using legacy suspend method i2c-core: driver [mag3110] using legacy resume method imx2-wdt imx2-wdt.0: IMX2+ Watchdog Timer enabled. timeout=60s (nowayout=1) device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com Bluetooth: HCI UART driver ver 2.2 Bluetooth: HCILL protocol initialized sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mmc0: SDHCI controller on platform [sdhci-esdhc-imx.2] using DMA sdhci sdhci-esdhc-imx.3: no write-protect pin available! mmc1: SDHCI controller on platform [sdhci-esdhc-imx.3] using DMA mxc_vdoa mxc_vdoa: i.MX Video Data Order Adapter(VDOA) driver probed VPU initialized mxc_asrc registered Galcore version 4.6.9.6622 Thermal calibration data is 0x56c4ba7d Thermal sensor with ratio = 179 usb 2-1: new high speed USB device number 2 using fsl-ehci Anatop Thermal registered as thermal_zone0 anatop_thermal_probe: default cooling device is cpufreq! usbcore: registered new interface driver usbhid usbhid: USB HID core driver usbcore: registered new interface driver snd-usb-audio mxc_hdmi_soc mxc_hdmi_soc.0: MXC HDMI Audio sgtl5000 0-000a: Failed to get supply 'VDDD': -19 print_constraints: 0-000a: 850 <--> 1600 mV at 1200 mV normal sgtl5000 0-000a: sgtl5000 revision 17 hub 2-1:1.0: USB hub found hub 2-1:1.0: 3 ports detected asoc: sgtl5000 <-> imx-ssi.1 mapping ok asoc: mxc-hdmi-soc <-> imx-hdmi-soc-dai.0 mapping ok ALSA device list: #0: sgtl5000-audio #1: imx-hdmi-soc NET: Registered protocol family 26 TCP cubic registered NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 can: controller area network core (rev 20090105 abi 8) NET: Registered protocol family 29 can: raw protocol (rev 20090105) can: broadcast manager protocol (rev 20090105 t) Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: HIDP (Human Interface Emulation) ver 1.2 lib80211: common routines for IEEE802.11 drivers VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 Bus freq driver module loaded Bus freq driver Enabled mxc_dvfs_core_probe DVFS driver module loaded snvs_rtc snvs_rtc.0: setting system clock to 1970-01-01 00:00:00 UTC (0) Waiting for root device /dev/sda2... usb 2-1.1: new low speed USB device number 3 using fsl-ehci input: USB Mouse as /devices/platform/fsl-ehci.1/usb2/2-1/2-1.1/2-1.1:1.0/input/input3 generic-usb 0003:04F3:0221.0001: input,hidraw0: USB HID v1.11 Mouse [USB Mouse] on usb-fsl-ehci.1-1.1/input0 usb 2-1.2: new high speed USB device number 4 using fsl-ehci scsi0 : usb-storage 2-1.2:1.0 scsi 0:0:0:0: Direct-Access SanDisk Cruzer 1.20 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 31266816 512-byte logical blocks: (16.0 GB/14.9 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sd 0:0:0:0: [sda] Attached SCSI removable disk EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (sda2): using internal journal EXT3-fs (sda2): mounted filesystem with writeback data mode VFS: Mounted root (ext3 filesystem) on device 8:2. devtmpfs: mounted Freeing init memory: 252K starting pid 1429, tty '': '/etc/rcS' Starting System done. Welcome to __________ .__ .___ __________ \______ \|__| __| _/ ____ ____ \______ \ __ __ ____ | _/| | / __ | / ___\ _/ __ \ | _/| | \ / \ | | \| |/ /_/ | / /_/ >\ ___/ | | \| | /| | \ |____|_ /|__|\____ | \___ / \___ >|____|_ /|____/ |___| / \/ \//_____/ \/ \/ \/ Embedded Linux Solutions For further information see: http://www.ridgerun.com Build host: RidgeRun-PC Built by: efernandez Build date: Mon, 03 Mar 2014 09:04:54 -0600 Build tag: nitrogen6x Configuring network interfaces eth0: Freescale FEC PHY driver [Micrel KSZ9021 Gigabit PHY] (mii_bus:phy_addr=1:06, irq=284) ADDRCONF(NETDEV_UP): eth0: link is not ready PHY: 1:06 - Link is Up - 100/Full ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Loading coprocessors modules... camera_reset: power_gp=0x6, reset_gp=0x8 reset_gp2=0xab ov564x_powerdown: powerdown=0, power_gp=0x6 ov564x_powerdown: powerdown=1, power_gp=0x6 Upload Auto-focus firmware camera ov5642 is found mxc_v4l2_master_attach: ipu0:/csi0 attached Starting D-Bus message bus system Framebuffer fb0 Resolution 1280 720 Screen resolution: 1280 x 720 HDMI display Search for input device none Mouse device is Framebuffer fb1 Display /dev/fb1 is not active Framebuffer fb2 Resolution 1024 600 Screen resolution: 1024 x 600 WSVGA display Search for input device ft5x06 Mouse device is tslib:/dev/input/event2 xres = 1024, yres = 600 Took 1 samples... Top left : X = 120 Y = 520 Took 1 samples... Top right : X = 120 Y = 520 Took 1 samples... Bot right : X = 120 Y = 520 Took 1 samples... Bot left : X = 120 Y = 520 Took 1 samples... Center : X = 120 Y = 520 ts_calibrate: determinant is too small -- 0.000000 Calibration failed. ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 Framebuffer fb3 Resolution 800 480 Screen resolution: 800 x 480 WVGA display Search for input device tsc2004 Mouse device is tslib:/dev/input/event1 xres = 800, yres = 480 Took 4 samples... Top left : X = 3741 Y = 594 Took 5 samples... Top right : X = 287 Y = 583 Took 3 samples... Bot right : X = 323 Y = 3582 Took 6 samples... Bot left : X = 3764 Y = 3533 Took 4 samples... Center : X = 2061 Y = 2075 808.991516 -0.203020 0.002023 -26.761047 0.000703 0.127969 Calibration constants: 53018068 -13305 132 -1753812 46 8386 65536 ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 Framebuffer fb4 Display /dev/fb4 is not active Configuring Demo... -> Identifying available displays... --> Using fb0 as main frame buffer for hdmi display.. --> Using fb1 as overlay frame buffer for hdmi display.. --> Using fb2 as main frame buffer for ldb display.. --> Using fb3 as main frame buffer for lcd display.. --> Using fb4 as overlay frame buffer for lcd display.. -> Using 3 displays... Starting Demo... Generating RSA key...Public key portion is: ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAAAgwC4clEWAVdgPc+5hSROweJ4X8B/JwPqdc8rgILxDDDTZZUyZIM92ZGEI60nZCsbNshhgWlNShc54htMjST8C27cZQpqZ4HYMi8a7jKRVzdKeaN7q0jy6nR6TcC4SL7izPELuVUDFrge2GbCkje+hoFuWGarpgREiTW7ccJr2x8gvJZ1 root@iMX6-Nitrogen6X Fingerprint: md5 50:17:8b:c4:d3:a7:40:d0:18:cc:86:ac:22:71:3d:50 Generating DSS key... -> Getting resolution for /dev/fb0... --> x = 1280... --> y = 720... -> Setting resolution for /dev/fb1... --> x = 1280... --> y = 720... -> Waiking fb0... pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 ipu_init_sync_panel: disp=1, pixel_clk=74250000 74250000 pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 -> Waiking fb1... pwm_config: pwm freq = 32786, clk_select=2 clock_rate=22000000 pwm_config: pwm freq = 20000, clk_select=2 clock_rate=22000000 Number of available screens: 3 Public key portion is: ssh-dss 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 root@iMX6-Nitrogen6X Fingerprint: md5 05:b4:1a:9d:72:5a:aa:a6:be:0c:02:3c:da:26:4d:6e Starting Dropbear SSH server: dropbear. Starting GStreamer Daemon Starting udev udevd[1630]: starting version 182 ov5640_csi1_camera_io_init camera_reset: power_gp=0x4d, reset_gp=0x4e reset_gp2=0xffffffff ov5640_csi1_camera_powerdown: powerdown=0, reset_gp=0x4e, power_gp=0x4d ov5640_read_reg:write reg error:reg=300a camera ov5640 is not found Please press Enter to activate this console. ov564x_powerdown: powerdown=0, power_gp=0x6 mxc_v4l_open: Mxc Camera no sensor ipu1/csi1 ov564x_powerdown: powerdown=1, power_gp=0x6 starting pid 1657, tty '/dev/ttymxc1': '-/bin/sh' BusyBox v1.20.2 (2014-03-03 07:52:21 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. / #