NVIDIA Jetson - Device Tree Overlay

Introduction

This wiki is intended to be used as a reference If you want to create a Device Tree (DT) overlay for a custom hardware module. DT overlay is used to configure various hardware devices that may be attached to the system.

Nvidia Jetson kernels use a Device Tree (DT) to describe the hardware present in the Nvidia Jetson board. You can use Jetson‑IO to support a custom hardware module by creating a device tree overlay for the hardware module to allow optional external hardware to be described and configured.

Create a device tree overlay

Jetson‑IO

NVIDIA provides the Jetson Expansion Header Tool (also known as Jetson‑IO), a Python script that runs on a Jetson developer kit and lets you apply a DT overlay configuration through a graphic user interface. Jetson‑IO finds the overlay file and allows you to apply it.

Device tree overlay structure

A device tree overlay for a hardware module must define the property:

• fragment: A DT overlay comprises a number of fragments, each of which targets one node and its subnodes.
• overlay-name: which specifies a name for the hardware module.
• jetson-header-name: which specifies the expansion header with which the hardware module is associated; must specify one of the values described in the table jetson-header-name property values.
• compatible: which indicates which combination of Jetson module and carrier board the overlay supports; must specify one or more of the values described in the table compatible property values.

Creating a Simple Device Tree Overlay

To create a simple device tree overlay to add a new custom property for Jetson Xavier NX Developer Kit and attach it to the 40‑pin expansion header, create a file named my-overlay.dts on the target platform with the following contents:

/dts-v1/;
/plugin/;
 
/ {
    overlay-name = "My Jetson Overlay Example";
    jetson-header-name = "Jetson 40pin Header";
    compatible = "nvidia,p3509-0000+p3668-0001";
 
    fragment@0 {
        target-path = "/";
        __overlay__ {
            my-custom-property = "This Is My Overlay";
        };
    };
};

Enter the following command to compile the DTS source file into an overlay file:

dtc -O dtb -o my-overlay.dtbo -@ my-overlay.dts

After you copy the new overlay file to the /boot directory, Jetson‑IO finds the overlay file and allows you to apply it, If you use an incorrect compatible value, the files is not listed

sudo cp my-overlay.dtbo /boot
sudo /opt/nvidia/jetson-io/config-by-hardware.py -l

Configuration listed from Xavier NX

Configurations for the following hardware modules are available:
1. Adafruit SPH0645LM4H
2. FE-PI Audio V1 and Z V2
3. My Jetson Overlay example
4. ReSpeaker 4 Mic Array

Apply the device tree overlay created

sudo /opt/nvidia/jetson-io/config-by-hardware.py -n "My Jetson Overlay example"

To apply the changes is required to reboot the board. after reboot the board you can read the new property defined in the device tree using the DT overlay.

cat /proc/device-tree/my-custom-property

Output:

This Is My Overlay

Remove overlay changes applied

The changes of the DT overlay are applied over the DT original and is created a new device tree. The name of the resulting device tree combines the original DT name and the overlay name.

/boot/kernel_tegra194-p3668-all-p3509-0000-my-jetson-overlay-example.dtb

To use the new DT creates a new entry in /boot/extlinux/extlinux.conf

This is the new entry added when is added the overlay LABEL My Jetson Overlay example MENU LABEL My Jetson Overlay example LINUX /boot/Image FDT /boot/kernel_tegra194-p3668-all-p3509-0000-my-jetson-overlay-example.dtb INITRD /boot/initrd APPEND ${cbootargs} quiet root=/dev/mmcblk0p1 rw rootwait rootfstype=ext4 console=ttyTCU0,115200n8 console=tty0 fbcon=map:0 net.ifnames=0