Release Notes for latest evaluation SDK for OMAP-L138 Hawkboard Board

From RidgeRun Developer Connection

Revision as of 20:19, 4 August 2010 by Dsoto (Talk | contribs)
Jump to:navigation, search

Contents

General Information

Release Information

Copyright Notice ©

This document and the software described in it are furnished under license with RidgeRun, and as such, may be used or copied only in accordance with the terms of the license. The contents of this document are furnished for informational purposes only and are subject to change without notice. RidgeRun, assumes no responsibility or liability for any errors or inaccuracies that may exist in this document. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form, without the prior written consent of RidgeRun.

Please read the full license agreement for the RidgeRun Evaluation SDKs .

Trademarks

ARM is a registered trademark of ARM Limited. Linux is a registered trademark of Linus Torvalds in the United States and other countries and is used by RidgeRun under license. Instruments and TI are registered trademarks of Texas Instruments Incorporated. All other trademarks are the property of their respective owners.

Revision History

Date Comments
NOT AVAILABLE Initial Version

Documentation

General SDK documentation:

SDK hints

$ sudo rm /bin/sh
  sudo ln -s /usr/bin/bash /bin/sh
$ sudo apt-get install libdbus-glib-1-dev gperf quilt

libtool: Version mismatch error.  This is libtool 2.2.6, but the
libtool: definition of this LT_INIT comes from libtool 2.2.6b.
libtool: You should recreate aclocal.m4 with macros from libtool 2.2.6
libtool: and run autoconf again

to fix this, the file local.tools (located in <yourSDKlocation>/OMAPL138SDK880207/bsp/oscheck) must be edited, the last line must be commented as is shown in the following example:

#mtd-tools:mtd-utils-git
automake:automake-1.11
valac:vala-0.7.9
#libtool:libtool-2.2.6

Finally, go to the directory <yourSDKlocation>/OMAPL138SDK880207/proprietary/gst-dmai-plugins and run the following commands:

$make
$autoreconf 
$quilt pop

Now, all should be ready to compile the SDK, then go to <yourSDKlocation>/OMAPL138SDK880207 and run:

$make 
                                            

OMAP-L138 Hawkboard Board Board related documentation:

  sudo ln -s /usr/bin/bash /bin/sh

Related links

What's New?

Supported Operating Systems

Linux Distribution

Setting up extra components

SDK Details

Integration with DSVDK

The DVSDK OMAP-L138_setuplinux_1_00_00_11.bin used can be find in


Features

Processor

Ti OMAP-L138 Low Power Application Processor
300-MHz ARM926EJ-STM RISC CPU
300-MHz C674x VLIW DSP
On-Chip RTC

Memory

128 MByte DDR2 SDRAM running at 150MHz
128 MByte NAND FLASH
1 SD/MMC Slot

Interfaces

One RS232 Serial Port
One Fast Ethernet Port (10/100 Mbps)
One USB Host port (USB 1.1)
One USB OTG port (USB 2.0)
One SATA Port (3Gbps)
One VGA Port (15 pin D-SUB)
Two AUDIO Ports (1 LINE IN & 1 LINE OUT)
One Composite IN (RCA Jack)

Expansion Interface

VPIF
UPP
PRU
LCDC
UART(x2)
SPI (x2)
I2C (x1)
eCAP
eHRPWM
GPIO

Software Support

U-Boot
Linux BSP: PSP SDK 03.20.00.11

Hardware

For details on the status of the basic drivers available on the RidgeRun SDK for Hawkboard, please visit Status of the hardware drivers on the Hawkboard page.

Software

Navigation
Toolbox