How to use GPIO signals

From RidgeRun Developer Connection

Revision as of 13:56, 14 March 2012 by Tfischer (Talk | contribs)
Jump to:navigation, search

Contents

References

GPIO Usage from a Linux Application

Overview

The following table summarizes the steps to configuring and using GPIO signals from a Linux application.

Step
Number
Action Description
1 Configure the kernel for GPIO support in sysfs Allow GPIO configuration and control from Linux applications (user space). The GPIO shoulw up in the system file system, sysfs, at /sys/class/gpio
2 Export GPIO to user space Each GPIO is are not accessible from user space until the GPIO has been exported. You can only export a GPIO that isn't owned by a Linux kernel driver
3 Configure GPIO for input or output To avoid hardware issues where two devices are driving the same signal, GPIOs default to be configured as an input. If you want to use the GPIO as an output, you need to change the configuration
4 Configure GPIO an an interrupt source If you have a GPIO that is an input, and you have an application you want to block waiting for the GPIO to change level, you can configure the GPIO as an interrupt source. You also need to configure if the interrupt occurs when the GPIO signal has a rising edge, a falling edge, or interrupts on both rising and falling edges. Once configured as an interrupt, your application can read the value file and the read will block until the interrupt occurs, then your application will return from the read system call and continue running.

The sysfs directory /sys/class/gpio contains subdirectories and files that are used for configuring and using GPIO signals from a Linux application.


File or
directory
Meaning Notes
/sys/class/gpio sysfs GPIO subdirectory Linux applications can configuration and use GPIO signals by accessing files in this subdirectory.
/sys/class/gpio/export Write-only file to expose a GPIO Before a Linux application can configuration and use a GPIO, the GPIO first has to be exported to user space by writing the GPIO number to this file.
/sys/class/gpio/gpio<<<number>>> Subdirectory for configuring and reading a specific GPIO signal Once a GPIO has been exported to user space, a new directory appears with a set of files that allow the GPIO to be configured and used by a Linux application
/sys/class/gpio/gpio<<<number>>>/direction Read-write supporting values of in and out
/sys/class/gpio/gpio<<<number>>>/value Read-write supporting values of 0 and 1
/sys/class/gpio/gpio<<<number>>>/edge Read-write supporting values of ' and '

Configure the kernel for GPIO support in sysfs

Symbol: GPIO_SYSFS [=y]
  Prompt: /sys/class/gpio/... (sysfs interface)
    Defined at drivers/gpio/Kconfig:51
    Depends on: GPIOLIB && SYSFS && EXPERIMENTAL
     Location:
      -> Kernel configuration
        -> Device Drivers
         -> GPIO Support (GPIOLIB [=y])
 

Enable GPIO access from user space

GPIO=22

cd /sys/class/gpio
ls
echo $GPIO > export
ls

Notice on the first ls that gpio22 doesn't exist, but does after you export GPIO 22 to user space.

cd /sys/class/gpio/gpio$GPIO
ls

There are files to set the direction and retrieve the current value.

echo "in" > direction
cat value

You can configure the GPIO for output and set the value as well.


echo "out" > direction
echo 1 > value

GPIO interrupts from user space

Reference

LeopoardBoard 365 GPIO 0 connection

On the LeopardBoard 365, the only GPIO I could find that was usable for interrupt input is GPIO0, also called CMOS_TRIGGER in the schematics. In looking at the schematics resistor R12 is not loaded and one of the pads connects to CMOS_TRIGGER. This R12 pad is the one closest to R11. If you hold the leopardboard 365 with the SD card slot facing you and rotate the board until the SD card slot is on the bottom edge, the the R12 pads are to the right of J6 and to the left of the SD card slot upper left corner.

Leopardboard365-gpio0-haywire.jpg

Using poll() to monitor for GPIO 0 change

The gpio-int-test.c program (or gpiopin.cpp for those who prefer C++) shows one way of using the sysfs file /sys/class/gpio/gpio0/value to block program execution using poll() until the input level on GPIO0 changes. The tricky part was figuring out to use POLLPRI instead of POLLIN as the event to monitor. You must have GPIO support in sysfs for this program to work (or you will not see the /sys/class/gpio directory).


The gpio-int-test.c program uses poll() to wake up every 3 seconds (using poll() timeout mechanism) at which time it prints a period. The poll() function is also watching for input from stdin and for an interrupt from GPIO 0.

Here is an example output. I started gpio-int to watch GPIO 0. I waited around 12 seconds (4 timeout periods), then pressed the letter 'a' twice followed by enter key. Then I shorted the haywire to 3.3V that is accessible on pin 5 on the JTAG connector. JTAG pin 5 is across from the JTAG missing pin). I exited the program using cntl-C.

/root # gpio-int 0 

....aa

poll() stdin read 0xA61

poll() stdin read 0xA61

poll() stdin read 0xA0A
..
poll() GPIO 0 interrupt occurred (len 0)

poll() GPIO 0 interrupt occurred (len 0)

poll() GPIO 0 interrupt occurred (len 0)

poll() GPIO 0 interrupt occurred (len 0)
..^C

Viewing GPIO Configuration

You can use debugfs to videw the current GPIO configuration. You may also be able to use debugfs to see if the GPIO pin is multiplex as a GPIO or is dedicated to some other function.

Configure the kernel to enable debugfs:

Symbol: DEBUG_FS [=y]
   Prompt: Debug Filesystem
     Defined at lib/Kconfig.debug:77
     Depends on: SYSFS     
     Location:
       -> Kernel configuration
         -> Kernel hacking         

Boot the target hardware and mount debugfs:

mount -t debugfs none /sys/kernel/debug

Dump the GPIO configuration.

cat /sys/kernel/debug/gpio

Dump the pin multiplexing configuration.

cat /sys/kernel/debug/omap_mux/board      # for OMAP
cat /sys/kernel/debug/dm365_mux           # for DM36x

Example shell script making it easy to set GPIOs from the command line

If you want to have a simple way to control a GPIO signal from the Linux command line, try the gpio.sh script below.

For examaple, if you want to read the value of GPIO 72 without setting its direction, try

gpio.sh 72


If you want to force GPIO 35 to be in input and read the current value, try

gpio.sh 35 in

If you want to configure GPIO 4 to be an output and set the value high, try

gpio.sh 4 out 1

For the script below to work, you need to first make sure you have build busybox with printf enabled.

#!bin/sh

show_usage()
{
    printf "\ngpio.sh <gpio pin number> [in|out [<value>]]\n"
}

if [ \( $# -eq 0 \) -o \( $# -gt 3 \) ] ; then
    show_usage
    printf "\n\nERROR: incorrect number of parameters\n"
    exit 255
fi

#doesn't hurt to export a gpio more than once
echo $1 > /sys/class/gpio/export

if [  $# -eq 1 ] ; then
   cat /sys/class/gpio/gpio$1/value
   exit 0
fi

if [ \( "$2" != "in" \) -a  \( "$2" != "out" \) ] ; then
    show_usage
    printf "\n\nERROR: second parameter must be 'in' or 'out'\n"
    exit 255
fi

echo $2 > /sys/class/gpio/gpio$1/direction

if [  $# -eq 2 ] ; then
   cat /sys/class/gpio/gpio$1/value
   exit 0
fi


VAL=$3

if [ $VAL -ne 0 ] ; then
    VAL=1
fi

echo $VAL > /sys/class/gpio/gpio$1/value
Navigation
Toolbox