LoepardBoard 365 Evaluation SDK Example Boot Output

From RidgeRun Developer Connection
Jump to: navigation, search

Leo365 Boot Output

Sept 8th 2010

Default SDK configuration. Host steps

cd $HOME/work
svn co  $REPO_URL leo365sdk # Get  $REPO_URL from http://www.ridgerun.com/downloadcenter.shtml
cd leo365sdk
`make env`
make installbootloader PORT=/dev/ttyUSB3
picocom -b 115200 -r -l /dev/ttyUSB3 # power cycle the board and stop in u-boot, exit picocom
make install PORT=/dev/ttyUSB3
picocom -b 115200 -r -l /dev/ttyUSB3 # power cycle the board boot to Linux

Boot output

U-Boot customized by RidgeRun

U-Boot 1.3.4-svn9 (Sep  8 2010 - 08:09:02)

I2C:   ready
DRAM:  128 MB
NAND:  NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Bad block table not found for chip 0
Bad block table not found for chip 0
nand_bbt: Error while writing bad block table -5
256 MiB
In:    serial
Out:   serial
Err:   serial
Ethernet PHY: GENERIC @ 0x00
Hit any key to stop autoboot:  0 

Loading from NAND 256MiB 3,3V 8-bit, offset 0x400000
   Image Name:   "RR Linux Kernel"
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4427904 Bytes =  4.2 MB
   Load Address: 80008000
   Entry Point:  80008000
Automatic boot of image at addr 0x82000000 ...
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   "RR Linux Kernel"
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4427904 Bytes =  4.2 MB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK

Starting kernel ...

Linux version 2.6.32-rc2-ridgerun (tfischer@sax-lx) (gcc version 4.2.4) #2 PREEMPT Wed Sep 8 08:04:58 MDT 2010
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: DM365 Leopard
Memory policy: ECC disabled, Data cache writeback
DaVinci dm365_rev1.2 variant 0x8
Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 13716
Kernel command line: davinci_enc_mngr.ch0_output=COMPONENT davinci_enc_mngr.ch0_mode=720P-60 davinci_display.cont2_bufsize=6291456 vpfe_capture.cont_bufoffset=6291456 vpfe_capture.cont_bufsize=6291456 console=ttyS0,115200n8 video=davincifb:vid0=off:vid1=off:osd1=off dm365_imp.oper_mode=0 davinci_capture.device_type=4 vpfe_capture.interface=1 mem=54M root=/dev/nfs nfsroot= rw ip=dhcp mtdparts=nand_davinci.0:3968k(UBOOT),128k(UBOOT_ENV),4352k(KERNEL),204800k(FS)
Unknown boot option `davinci_capture.device_type=4': ignoring
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 54MB = 54MB total
Memory: 50124KB available (3980K code, 385K data, 148K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
Console: colour dummy device 80x30
Calibrating delay loop... 147.86 BogoMIPS (lpj=739328)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
DaVinci: 8 gpio irqs
NET: Registered protocol family 16
davinci_serial_init:97: failed to get UART2 clock
bio: create slab <bio-0> at 0
DM365 IPIPE initialized in Continuous mode
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
vpss vpss: dm365_vpss vpss probed
vpss vpss: dm365_vpss vpss probe success
ch0 default output "COMPONENT", mode "720P-60"
VPBE Encoder Initialized
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: US
        (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
        (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
        (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
        (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
cfg80211: Calling CRDA for country: US
LogicPD encoder initialized
Leopard DVI encoder initialized
Switching to clocksource timer0_1
musb_hdrc: version 6.0, cppi-dma, host, debug=0
musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
msgmni has been set to 98
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
davincifb davincifb.0: dm_osd0_fb: 1280x720x16@0,0 with framebuffer size 1800KB
davincifb davincifb.0: dm_osd1_fb: 1280x720x4@0,0 with framebuffer size 1800KB
DM365 IPIPEIF probed
imp serializer initialized
davinci_previewer initialized
davinci_resizer initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
console [ttyS0] enabled
brd: module loaded
console [netcon0] enabled
netconsole: network logging started
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
i2c /dev entries driver
Linux video capture interface: v2.00
ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter)
vpfe-capture: vpss clock vpss_master enabled
vpfe-capture vpfe-capture: v4l2 device registered
vpfe-capture vpfe-capture: video device registered
Leopard: switch to HD imager-MT9P031 video input
mt9p031 1-0048: No MT9P031 chip detected, register read ffffff87
vpfe-capture vpfe-capture: v4l2 sub device mt9p031 register fails
No sub devices registered
vpfe-capture: vpfe capture clocks disabled
vpfe_register_ccdc_device: DM365 ISIF
DM365 ISIF is registered with vpfe.
af major#: 252, minor# 0
AF Driver initialized
aew major#: 251, minor# 0
AEW Driver initialized
Trying to register davinci display video device.
Trying to register davinci display video device.
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
watchdog watchdog: heartbeat 60 sec
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
No device for DAI tlv320aic3x
No device for DAI davinci-i2s
asoc: tlv320aic3x <-> davinci-i2s mapping ok
ALSA device list:
  #0: DaVinci EVM (tlv320aic3x)
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
Clocks: disable unused mmcsd1
Clocks: disable unused spi0
Clocks: disable unused spi1
Clocks: disable unused spi2
Clocks: disable unused spi3
Clocks: disable unused spi4
Clocks: disable unused aemif
Clocks: disable unused pwm0
Clocks: disable unused pwm1
Clocks: disable unused pwm2
Clocks: disable unused pwm3
Clocks: disable unused timer1
Clocks: disable unused timer3
Clocks: disable unused emac
Clocks: disable unused voice_codec
Clocks: disable unused rto
Clocks: disable unused mjcp
davinci_emac_probe: using random MAC addr: 42:75:c0:35:84:ec
emac-mii: probed
mmc0: host does not support reading read-only switch. assuming write-enable.
mmc0: new SD card at address aaaa
mmcblk0: mmc0:aaaa SU02G 1.84 GiB 
 mmcblk0: p1
Sending DHCP requests .., OK
IP-Config: Got DHCP answer from, my address is
IP-Config: Complete:
     device=eth0, addr=, mask=, gw=,
     host=, domain=fischerfamily.org, nis-domain=fischerfamily.org,
     bootserver=, rootserver=, rootpath=
Looking up port of RPC 100003/2 on
Looking up port of RPC 100005/1 on
VFS: Mounted root (nfs filesystem) on device 0:14.
Freeing init memory: 148K
init started: BusyBox v1.14.2 (2010-09-07 15:32:06 MDT)
starting pid 977, tty '': '/etc/rcS'
Starting System
Welcome to
__________ .__     .___               __________                
\______   \|__|  __| _/  ____    ____ \______   \ __ __   ____  
 |       _/|  | / __ |  / ___\ _/ __ \ |       _/|  |  \ /    \ 
 |    |   \|  |/ /_/ | / /_/  >\  ___/ |    |   \|  |  /|   |  \
 |____|_  /|__|\____ | \___  /  \___  >|____|_  /|____/ |___|  /
        \/          \//_____/       \/        \/             \/ 
    Embedded Linux Solutions
For further information see:
Build host: sax-lx
Built by: tfischer
Build date: Wed, 08 Sep 2010 08:08:24 -0600
Build tag: leopard
Configuring network interfaces

Please press Enter to activate this console. 
starting pid 1050, tty '/dev/ttyS0': '-/bin/sh'

BusyBox v1.14.2 (2010-09-07 15:32:06 MDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

/ #